Franklin Electric CERUS X-DRIVE CXD-003A-4V, Installation And Operation Manual

Page: 223 / 252

PARAMETER REFERENCE TABLES
Parameter Descriptions > COMM Menu
223
Parameter Descriptions > COMM Menu
AR = Adjustable while running.
PROT-43 1067 Y Spd Search Gain 1 to 200% Speed search gain: Voltage gain percentage for speed search operation.
Reduce value if overload or over-current fault occurs.
PROT-44 1068 Y IPF Restart Dly 0.0 to 5.0 sec Delay for restart after an Instantaneous Power Failure. Set value high
enough to allow residual regeneration voltage to disappear.
PROT-45 1069 Y Fan Control 0_At Power-Up
1_Delayed Stop
2_During Run
3_By Temperature
4_Disabled
Determines operation of fan. It is not recommended to set to 4_Disabled
since this will reduce performance of drive.
3_Starts fan at 60 °C
PROT-46 1070 Y Last Flt Freq 0.00 to 599.00 Hz Output frequency at last fault (Read Only)
PROT-47 1071 Y Last Flt IGBTT -3277 to 3276.7 °C IGBT temperature at last fault (Read Only)
PROT-48 1072 Y Last Flt Cap T -3277 to 3276.7 °C Capacitance temperature at last fault (Read Only)
PROT-49 1073 Y Last Flt MFI 0000h to FFFFh Status of Multi-function input terminals at last fault (Read Only)
PROT-50 1074 Y Last Flt MFO 0000h to FFFFh Status of Multi-function output terminals at last fault (Read Only)
PROT-51 1075 Y Fault-1 Record 0 to 65535 First register of fault listing. (Read Only)
PROT-52 1076 Y Fault-2 Record 0 to 65535 Second register of fault listing. (Read Only)
PROT-53 1077 Y Fault-3 Record 0 to 65535 Third register of fault listing. (Read Only)
PROT-54 1078 Y Fault-4 Record 0 to 65535 Fourth register of fault listing. (Read Only)
PROT-55 1079 Y Fault-5 Record 0 to 65535 Fifth register of fault listing. (Read Only)
PROT-56 1080 Y Fault-6 Record 0 to 65535 Sixth register of fault listing. (Read Only)
PROT-57 1081 Y ULD Torque Min 5% to [SET-42] Sets minimum torque level % at 0Hz when using Underload Torque.
PROT-58 1082 Y HLD Torque Min [PROT-57] to [SET-48] Sets minimum torque level % at 0Hz when using High load Torque.
CODE Mod
Bus AR Display Name
Range Description
CODE
Mod
Bus AR Display Name
Range Description
Comm-00 1280 Y COM1 Address 1 to 254 RS485 address of VFD.
Comm-01 1281 Y COM1 Speed 4.8 to 115.2 Kbps RS485 baud rate. All devices on RS485 communication must have the
same baud rate.
Comm-02 1282 Y COM1 Loss 0_Alarm and Run
1_Trip Decel Stop
2_Trip Coast Stop
3_Disabled
Select operation when communication is lost.
Comm-03 1283 Y COM1 Loss Delay 0.0 to 100.0 sec Duration of communication loss before initiating operation.
Comm-04 1284 Y COM1 Protocol 1_7, N, 2 for ASCII
2_7, E, 1 for ASCII
3_7, O, 1 for ASCII
4_7, E, 2 for ASCII
5_7, O, 2 for ASCII
6_8, N, 1 for ASCII
7_8, N, 2 for ASCII
8_8, E, 1 for ASCII
9_8, O, 1 for ASCII
10_8, E, 2 for ASCII
11_8, O, 2 for ASCII
12_8, N, 1 for RTU
13_8, N, 2 for RTU
14_8, E, 1 for RTU
15_8, O, 1 for RTU
16_8, E, 2 for RTU
17_8, O, 2 for RTU
RS485 Protocol: Data Bits - Parity - Stop Bits - Message Format
Comm-05 1285 Y Response Delay 0.0 to 200.0 ms Duration VFD waits before responding to received communication.