Foma N902iX, Manual

Page: 484 / 574

482
* The miniSD memory card is optional for use in this terminal.
→
p.371
If An
y
Er
ro
r
Me
ss
a
g
e
Appe
ar
s
Appendix/External Devices/Troubleshooting
“Connection interrupted”
d
i-mode connection was interrupted due to poor reception. Move to a
location where the reception is good before using the i-mode service.
d
If this message appears even when the reception is good and “ ”
appears, the site you are accessing is busy. Retry later.
p.215
−
“Continue using i-
α
ppli and
transmit data?”
d
This message appears when you select “NO” or “Terminate i-
α
ppli”
in response to the message “Data transmission is frequent Continue
transmission?”. Select “YES” to continue i-
α
ppli communication. To
quit using an i-
α
ppli program, select “Terminate i-
α
ppli”.
−
“Could not read”
d
The data cannot be copied due to some error. Exchange with a new
miniSD memory card then retry to copy. −
“Data in IC card is full Replace?”
d
This message appears when you attempt to download Osaifu-Keitai
i-
α
ppli but the space is not enough on the IC card. Select “YES” to
display already registered Osaifu-Keitai services and the space
(bytes) on the IC card. Check the size required, select services to
remove, and launch i-
α
ppli to remove them.
−
“Data is too long A part is deleted”
d
The size of address, subject or text or more than one data exceeds
the maximum, and the Compose message screen appears with the
excess part deleted.
−
“Data is too long Please delete
message”
d
The total length of the message text and quotation mark characters
in the i-mode message to be quoted in a reply exceeds 5,000
double-byte characters. Delete some of the text to reduce the
character count to 5,000 double-byte characters or fewer.
−
“Data transmission is frequent
Continue transmission?”
d
This message appears when the number of communications that are
using i-
α
ppli and have been established in a given time is extremely
large. Select “YES” to continue to make i-
α
ppli communication, or
“NO” to quit the communication. To quit using an i-
α
ppli program,
select “Terminate i-
α
ppli”.
−
“Data transmission is frequent
Press CLR and confirm data
transmission”
d
This message appears when the number of communications
established from the i-
α
ppli standby screen in a given time is
extremely large. Press
t
to select whether to permit
communication from the i-
α
ppli standby screen or whether to exit the
i-
α
ppli standby screen.
p.318
“Download failed”
d
This message appears if a communication error occurs or a data
contains an error when you attempt to download data such as a
melody, Chara-den character or download dictionary.
−
“Editing now Cannot delete”
d
This message appears when you attempt to delete a mail message
that is stored in the Draft and being edited.
−
“Enter correct Network Security
Code”
d
This message appears when you need to enter the network security
code for a function but a wrong number was entered. Enter the
correct network security code. p.156
“Error in image Does not work
correctly”
d
This message appears when a Flash movie cannot be played due to
an error found in the data.
−
“Error Register forwarding
number”
d
This message appears when you have subscribed to the Call
Forwarding service and attempt to forward an incoming call by
selecting “Call Forwarding” from the function menu without setting
the forwarding number. p.427
“Exceeds max number of
simultaneous calls”
d
You can make a PTT call to a maximum of four people at the same
time.
−
“Failed to Copy all”
d
The data cannot be copied due to some error. Exchange with a new
miniSD memory card then retry to copy.
−
“Failed to Copy this“
d
The data cannot be copied due to some error. Exchange with a new
miniSD memory card then retry to copy.
−
“Format miniSD for your phone”
d
There is an error e.g. the miniSD memory card is not formatted.
Reformat the miniSD memory card. p.379
“Frame number of this page is not
supported”
d
The webpage cannot be displayed because the frame count exceeds
the maximum that can be displayed on Full Browser.
−
“Function cannot operate any
more”
d
Exit another function before operating.
−
Error Message Explanation and Solution Refer to