manualshive.com logo in svg

Danfoss VLT AutomationDrive FC 301, Programming Manual, Page: 501 / 722

Share
Download
Danfoss VLT AutomationDrive FC 301 Programming Manual Download Page 501

-

-

Readout of the mechanical power applied to the motor shaft. The base unit is in W.

Parameter 16-24 Calibrated Stator Resistance

Table 845: Parameter 16-24 Calibrated Stator Resistance

16-24 Calibrated Stator Resistance

Default value: 0.0000 Ohm

Parameter type: Range, 0.0000 - 100.0000 Ohm

Setup: All setups

Conversion index: -4

Data type: Uint32

Change during operation: True

Shows the calibrated stator resistance.

Parameter 16-25 Torque [Nm] High

Table 846: Parameter 16-25 Torque [Nm] High

16-25 Torque [Nm] High

Default value: 0 Nm

Parameter type: Range, -200000000 - 200000000 Nm

Setup: All setups

Conversion index: -1

Data type: Int32

Change during operation: False

View the torque value with sign, applied to the motor shaft. Some motors supply more than 160% torque. Therefore, the minimum
value and the maximum value depend on the maximum motor current as well as the motor used. This specific readout has been
adapted to be able to show higher values than the standard readout in 

parameter 16-16 Torque [Nm]

.

Parameter 16-28 Angle Error

Table 847: Parameter 16-28 Angle Error

16-28 Angle Error

Default value: 0 °

Parameter type: Range, -180 - 180 °

Setup: All setups

Conversion index: -2

Data type: Int16

Change during operation: False

Readout of the deviation between sensorless rotor angle estimation by motor controller and real rotor angle based on encoder
reading. The parameter is only activated if options in 

parameter 1-01 Motor Control Principle

 is set to 

[2] Flux Sensorless

 and 

parameter

1-10 Motor Construction

 is set to 

[1] PM, non salient SPM

 or 

[2] PM, salient IPM

. The encoder source used for comparison must be

selected in 

parameter 7-00 Speed PID Feedback Source

. To obtain an accurate reading of 

parameter 16-28 Angle Error

, the motor angle

offset must be set in 

parameter 1-41 Motor Angle Offset

. Rotor detection is configured in 

parameter 7-90 Position PI Feedback Source

,

which is activated using the setting in 

parameter 1-70 Start Mode

 in Flux with motor feedback. 

Parameter 7-90 Position PI Feedback

Source

 must be set to 

[0] Motor feedb.P1-02

. The encoder is then only used for comparison while position control is based on the

estimated sensorless position. This enables the measurement of the accuracy of position control in sensorless mode.

5.16.3 16-3* Drive Status

N O T I C E

The following parameters are only available in FC 302:

Parameter 16-31 System Temp.
Parameter 16-49 Current Fault Source

Parameter 16-30 DC Link Voltage

Table 848: Parameter 16-30 DC Link Voltage

16-30 DC Link Voltage

Default value: 0 V

Parameter type: Range, 0 - 10000 V

Setup: All setups

Conversion index: 0

Data type: Uint16

Change during operation: False

View a measured value. The value is filtered with a 30 ms time constant.

AU275636650261en-000101 / 130R0334 | 501

Danfoss A/S © 2022.12

Parameter Descriptions

VLT AutomationDrive FC 301/302

Programming Guide

Summary of Contents for VLT AutomationDrive FC 301



















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments