manualshive.com logo in svg

Danfoss VLT AutomationDrive FC 301, Programming Manual, Page: 259 / 722

Share
Download
Danfoss VLT AutomationDrive FC 301 Programming Manual Download Page 259

Par 7-07=1.00

Par 7-07=n1/n2

e3

0b

a8

71

.1

0

Motor

n1

n2

Illustration 75: Speed PID Feedback Gear Ratio

Parameter 7-08 Speed PID Feed Forward Factor

Table 455: Parameter 7-08 Speed PID Feed Forward Factor

7-08 Speed PID Feed Forward Factor

Default value: 0%

Parameter type: Range, 0 - 500%

Setup: All setups

Conversion index: 0

Data type: Uint16

Change during operation: False

The reference signal bypasses the speed controller by the amount specified. This feature increases the dynamic performance of the
speed control loop.

Parameter 7-09 Speed PID Error Correction w/Ramp

Table 456: Parameter 7-09 Speed PID Error Correction w/Ramp

7-09 Speed PID Error Correction w/Ramp

Default value: Size related

Parameter type: Range, 10 - 100000 RPM

Setup: All setups

Conversion index: 67

Data type: Uint32

Change during operation: True

The speed error between ramp and actual speed is held up against the setting in this parameter. If the speed error exceeds this
parameter entry, the speed error is corrected via ramping in a controlled way.

M ot or 

T ime 

Speed 

Er r or 

T or que 

Limit 

Speed 

e3

0b

c0

26

.1

1 

M ot or 

T ime 

Speed 

Er r or 

T or que 

Limit 

Speed 

R amp 

M ot or Speed 

Illustration 76: Speed Error Between Ramp and Actual Speed

5.8.4 7-1* Torque PI Control

Parameters for configuring the torque PI control.

AU275636650261en-000101 / 130R0334 | 259

Danfoss A/S © 2022.12

Parameter Descriptions

VLT AutomationDrive FC 301/302

Programming Guide

Summary of Contents for VLT AutomationDrive FC 301



















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments