manualshive.com logo in svg

Danfoss VLT AutomationDrive FC 301, Programming Manual, Page: 262 / 722

Share
Download
Danfoss VLT AutomationDrive FC 301 Programming Manual Download Page 262

5.8.6 7-3* Process PID Ctrl.

Parameter 7-30 Process PID Normal/ Inverse Control

Table 462: Parameter 7-30 Process PID Normal/ Inverse Control

7-30 Process PID Normal/ Inverse Control

Default value: [0] Normal

Parameter type: Option

Setup: All setups

Conversion index: –

Data type: Uint8

Change during operation: True

Normal and inverse controls are implemented by introducing a difference between the reference signal and the feedback signal.

Option

Name

Description

[0]*

Normal

Set the process to increase the output frequency.

[1]

Inverse

Set the process to decrease the output frequency.

Parameter 7-31 Process PID Anti Windup

Table 463: Parameter 7-31 Process PID Anti Windup

7-31 Process PID Anti Windup

Default value: [1] On

Parameter type: Option

Setup: All setups

Conversion index: –

Data type: Uint8

Change during operation: True

Normal and inverse controls are implemented by introducing a difference between the reference signal and the feedback signal.

Option

Name

Description

[0]

Off

Continue regulation of an error even when the output frequency cannot be increased or decreased.

[1]*

On

Cease regulation of an error when the output frequency can no longer be adjusted.

Parameter 7-32 Process PID Start Speed

Table 464: Parameter 7-32 Process PID Start Speed

7-32 Process PID Start Speed

Default value: 0 RPM

Parameter type: Range, 0 - 6000 RPM

Setup: All setups

Conversion index: 67

Data type: Uint16

Change during operation: True

Enter the motor speed to be attained as a start signal for commencement of PID control. When the power is switched on, the drive
starts to ramp and then operates under speed open-loop control. When the process PID start speed is reached, the drive changes to
process PID control.

Parameter 7-33 Process PID Proportional Gain

Table 465: Parameter 7-33 Process PID Proportional Gain

7-33 Process PID Proportional Gain

Default value: 0.10

Parameter type: Range, 0 - 10

Setup: All setups

Conversion index: -2

Data type: Uint16

Change during operation: True

Enter the PID proportional gain. The proportional gain multiplies the error between the setpoint and the feedback signal.

AU275636650261en-000101 / 130R0334

262 | Danfoss A/S © 2022.12

Parameter Descriptions

VLT AutomationDrive FC 301/302

Programming Guide

Summary of Contents for VLT AutomationDrive FC 301



















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments