Cadillac Escalade 2020 Owner'S Manual Download Page 208 | Manualshive

Page: 208 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

208

DRIVING AND OPERATING

when driving on downhill grades by
using the engine and transmission to
slow the vehicle.

To disable and enable Cruise Grade
Braking for the current ignition cycle,
press and hold the Tow/Haul button
for five seconds. A Driver Information
Center (DIC) message displays.

For other forms of Grade Braking, see

Automatic Transmission

and

Tow/Haul Mode

Ending Cruise Control

There are four ways to end cruise
control:

.

Step lightly on the brake pedal.

.

Press

*

.

.

Shift the transmission to
N (Neutral).

.

To turn off cruise control,
press

J

.

Erasing Speed Memory

The cruise control set speed is erased
from memory if

J

is pressed or if

the ignition is turned off.

Adaptive Cruise Control

If equipped with Adaptive Cruise
Control (ACC), it allows for selecting
the cruise control set speed and
following gap. Read this entire section
before using this system. ACC uses a
camera and radar sensors to detect
other vehicles. The following gap is
the following time (or distance)
between your vehicle and a vehicle
detected directly ahead in your path,
moving in the same direction. If no
vehicle is detected in your path, ACC
works like regular cruise control.

If a vehicle is detected in your path,
ACC can speed up the vehicle or apply
limited, moderate braking to maintain
the selected following gap. To
disengage ACC, apply the brake. If the
Traction Control System (TCS) or
electronic stability control system
activates while ACC is engaged, ACC
may automatically disengage. See

Traction Control/Electronic Stability
Control

. When road conditions

allow ACC to be safely used, the ACC
can be turned back on.

ACC will not engage if the TCS or
StabiliTrak electronic stability control
system is disabled.

{

Warning

ACC has limited braking ability and
may not have time to slow the
vehicle down enough to avoid a
collision with another vehicle you
are following. This can occur when
vehicles suddenly slow or stop
ahead, or enter your lane. Also see

“

Alerting the Driver

”

in this section.

Complete attention is always
required while driving and you
should be ready to take action and
apply the brakes. See

{

Warning

ACC will not detect or brake for
children, pedestrians, animals,
or other objects.

(Continued)

«
...
206
207
208
209
210
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: Acdeos Pages: 7

Brand: Quadratec Pages: 8

Brand: Warrior Winches Pages: 17

Brand: GARO Pages: 2

Prestige APS-45B

Brand: Audiovox Pages: 8

Brand: Volvo Pages: 138

CARPOWER CAP-12XHQ

Brand: Monacor Pages: 5

Grand Cherokee WK2

Brand: Jeep Pages: 338

Brand: Mazdaspeed Pages: 8

Brand: Yakima Pages: 19

UCI-11C NTV-KIT331

Brand: Nav TV Pages: 4

Brand: Hama Pages: 75

Brand: Harbor Freight Tools Pages: 12

Brand: Honda Pages: 3

Brand: FALCON RIDGE Pages: 8

Brand: Scosche Pages: 8

Brand: Hella Pages: 21

Brand: ULTIMATE SPEED Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands