Cadillac Escalade 2020 Owner'S Manual Download Page 127 | Manualshive

Page: 127 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

INSTRUMENTS AND CONTROLS

127

the tires to the pressure value shown
on the Tire and Loading Information
label. See

Tire Pressure

When the Light Flashes First and
Then Is On Steady

If the light flashes for about a minute
and then stays on, there may be a
problem with the TPMS. If the
problem is not corrected, the light will
come on at every ignition cycle. See

Tire Pressure Monitor Operation

Engine Oil Pressure Light

Caution

Lack of proper engine oil
maintenance can damage the
engine. Driving with the engine oil
low can also damage the engine.
The repairs would not be covered
by the vehicle warranty. Check the
oil level as soon as possible. Add oil
if required, but if the oil level is
within the operating range and the
oil pressure is still low, have the

(Continued)

Caution (Continued)

vehicle serviced. Always follow the
maintenance schedule for changing
engine oil.

This light should come on briefly as
the engine is started. If it does not
come on, have the vehicle serviced by
your dealer.

If the light comes on and stays on, it
means that oil is not flowing through
the engine properly. The vehicle could
be low on oil and might have some
other system problem. See your dealer.

Low Fuel Warning Light

This light is near the fuel gauge and
comes on briefly when the ignition is
turned on as a check to show it is
working.

It also comes on when the fuel tank is
low on fuel. The light turns off when
fuel is added. If it does not, have the
vehicle serviced.

Security Light

The security light should come on
briefly as the engine is started. If it
does not come on, have the vehicle

«
...
125
126
127
128
129
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: cam Pages: 28

Brand: Parrot Pages: 19

Brand: Parrot Pages: 88

Brand: Parrot Pages: 2

Brand: Parrot Pages: 2

CK 3000 Evolution

Brand: Parrot Pages: 8

CK 3000 Evolution

Brand: Parrot Pages: 106

BLACK STEEL S2560

Brand: Fab Fours Pages: 9

KO PROPO RTF 2002 ESC

Brand: Tamiya Pages: 2

Brand: Lincoln Pages: 424

Brand: Volkswagen Pages: 26

FIX&GO automatic

Brand: Alfa Romeo Pages: 40

Brand: AutoWatch Pages: 4

Brand: JANE Pages: 58

Brand: Mitsubishi Pages: 19

Brand: Oypla Leisure Pages: 4

Brand: Oldsmobile Pages: 354

Brand: Carcomm Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands