manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

174

DRIVING AND OPERATING

occur if the exhaust pipe is under
water. Do not turn off the ignition
when driving through water. If the
exhaust pipe is under water, the
engine will not start. When going
through water, the brakes get wet and
it may take longer to stop. See

“

Driving on Wet Roads

”

later in this

section.

After Off-Road Driving

Remove any brush or debris that has
collected on the underbody or chassis,
or under the hood. These
accumulations can be a fire hazard.

After operation in mud or sand, have
the brake linings cleaned and checked.
These substances can cause glazing
and uneven braking. Check the body
structure, driveline, steering,
suspension, wheels, tires, and exhaust
system for damage and check the fuel
lines and cooling system for any
leakage.

More frequent maintenance service is
required. See the

Maintenance Schedule

0

329

.

Driving on Wet Roads

Rain and wet roads can reduce vehicle
traction and affect your ability to stop
and accelerate. Always drive slower in
these types of driving conditions and
avoid driving through large puddles
and deep-standing or flowing water.

{

Warning

Wet brakes can cause crashes. They
might not work as well in a quick
stop and could cause pulling to one
side. You could lose control of the
vehicle.

After driving through a large puddle
of water or a car/vehicle wash,
lightly apply the brake pedal until
the brakes work normally.

Flowing or rushing water creates
strong forces. Driving through
flowing water could cause the
vehicle to be carried away. If this
happens, you and other vehicle
occupants could drown. Do not

(Continued)

Warning (Continued)

ignore police warnings and be very
cautious about trying to drive
through flowing water.

Hydroplaning

Hydroplaning is dangerous. Water can
build up under the vehicle's tires so
they actually ride on the water. This
can happen if the road is wet enough
and you are going fast enough. When
the vehicle is hydroplaning, it has
little or no contact with the road.

There is no hard and fast rule about
hydroplaning. The best advice is to
slow down when the road is wet.

Other Rainy Weather Tips

Besides slowing down, other wet
weather driving tips include:

.

Allow extra following distance.

.

Pass with caution.

.

Keep windshield wiping equipment
in good shape.

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Vauxhall MOVANO Owner'S Manual preview
MOVANO
Brand: Vauxhall Pages: 177
Mobis G4211ADE00AL Installation Instructions Manual preview
G4211ADE00AL
Brand: Mobis Pages: 16
Subaru starlink Manual preview
starlink
Brand: Subaru Pages: 216
Kia 2016 Cadenza Owner'S Manual preview
2016 Cadenza
Brand: Kia Pages: 419
Prorack K383 Fitting Instructions Manual preview
K383
Brand: Prorack Pages: 14
Victory 4x4 5TH GEN 4RUNNER Install Instructions preview
5TH GEN 4RUNNER
Brand: Victory 4x4 Pages: 5
Keith WALKING FLOOR Helpful Hints preview
WALKING FLOOR
Brand: Keith Pages: 2
Whispbar K934W Fitting Instructions Manual preview
K934W
Brand: Whispbar Pages: 15
Dacia 2014 Sandero Driver'S Handbook Manual preview
2014 Sandero
Brand: Dacia Pages: 238
Mercedes-Benz AMG E-Class Supplement Manual preview
AMG E-Class
Brand: Mercedes-Benz Pages: 54
CTEK D250S Dual Manual preview
D250S Dual
Brand: CTEK Pages: 84
Zap XEBRA ZAPCAR Series Owner'S Manual preview
XEBRA ZAPCAR Series
Brand: Zap Pages: 16
MVG 0845 C Manual preview
0845 C
Brand: MVG Pages: 18
Omix-Ada Alloy Rugged Ridge X-Clamp Manual preview
Alloy Rugged Ridge X-Clamp
Brand: Omix-Ada Pages: 2
Dodge 8W-70 Wiring Diagram preview
8W-70
Brand: Dodge Pages: 3
Saab 32 025 603 Installation Instructions Manual preview
32 025 603
Brand: Saab Pages: 15
Waeco Magic Watch MWE-850-4DSM Installation And Operating Manual preview
Magic Watch MWE-850-4DSM
Brand: Waeco Pages: 204
FORM FIT 8F 00 Installation Instructions preview
8F 00
Brand: FORM FIT Pages: 2

Brands by name

Popular brands

Load more brands