Cadillac Escalade 2020 Owner'S Manual Download Page 288 | Manualshive

Page: 288 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

288

VEHICLE CARE

Warning (Continued)

.

Replace any tires that have
been damaged by impacts
with potholes, curbs, etc.

.

Improperly repaired tires
can cause a crash. Only
the dealer or an authorized
tire service center should
repair, replace, dismount,
and mount the tires.

.

Do not spin the tires in
excess of 56 km/h
(35 mph) on slippery
surfaces such as snow,
mud, ice, etc. Excessive
spinning may cause the
tires to explode.

See

Tire Pressure for High-Speed

for inflation

pressure adjustment for
high-speed driving.

All-Season Tires

This vehicle may come with all-season
tires. These tires are designed to
provide good overall performance on
most road surfaces and weather
conditions. Original equipment tires
designed to GM's specific tire
performance criteria have a TPC
specification code molded onto the
sidewall. Original equipment
all-season tires can be identified by
the last two characters of this TPC
code, which will be

“

MS.

”

Consider installing winter tires on the
vehicle if frequent driving on snow or
ice-covered roads is expected.
All-season tires provide adequate
performance for most winter driving
conditions, but they may not offer the
same level of traction or performance
as winter tires on snow or ice-covered
roads. See

Winter Tires

This vehicle was not originally
equipped with winter tires. Winter
tires are designed for increased
traction on snow and ice-covered

roads. Consider installing winter tires
on the vehicle if frequent driving on
ice or snow covered roads is expected.
See your dealer for details regarding
winter tire availability and proper tire
selection. Also, see

Buying New Tires

With winter tires, there may be
decreased dry road traction, increased
road noise, and shorter tread life.
After changing to winter tires, be alert
for changes in vehicle handling and
braking.

If using winter tires:

.

Use tires of the same brand and
tread type on all four wheel
positions.

.

Use only radial ply tires of the
same size, load range, and speed
rating as the original equipment
tires.

Winter tires with the same speed
rating as the original equipment tires
may not be available for H, V, W, Y,
and ZR speed rated tires. If winter
tires with a lower speed rating are
chosen, never exceed the tire's
maximum speed capability.

«
...
286
287
288
289
290
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: Daihatsu Pages: 485

Brand: TATA Motors Pages: 161

Brand: TAUBENREUTHER Pages: 11

Brand: Yakima Pages: 15

Brand: Paxton Automotive Pages: 85

Brand: Thule Pages: 8

Brand: MAXWORKS Pages: 7

Brand: P-Invent Pages: 4

Brand: Vauxhall Pages: 259

Brand: RAM Pages: 13

Brand: Cadillac Pages: 20

Brand: Hyundai Pages: 168

SHERPA SADDLE BAG JL

Brand: Overland Outfitters Pages: 2

Brand: TracRac Pages: 6

Brand: Bazooka Pages: 2

Brand: GMC Pages: 40

Brand: Edelbrock Pages: 3

Brand: Peiying Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands