Cadillac Escalade 2020 Owner'S Manual Download Page 244 | Manualshive

Page: 244 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

244

DRIVING AND OPERATING

allowable tongue weight for the
vehicle or 227 kg (500 lb), whichever
is less.

Rear Gross Axle Weight Rating
(GAWR-RR)

The GAWR-RR is the total weight that
can be supported by the rear axle of
the vehicle. Do not exceed the
GAWR-RR for the vehicle, with the
tow vehicle and trailer fully loaded for
the trip including the weight of the
trailer tongue. If using a
weight-distributing hitch, do not
exceed the GAWR-RR before applying
the weight distribution spring bars.

Ask your dealer for trailering
information or assistance.

Towing Equipment

Hitches

Always use the correct hitch
equipment for your vehicle.
Crosswinds, large trucks going by, and
rough roads can affect the trailer and
the hitch.

Proper hitch equipment for your
vehicle helps maintain control of the
vehicle-trailer combination. Many
trailers can be towed using a
weight-carrying hitch which has a
coupler latched to the hitch ball, or a
tow eye latched to a pintle hook.
Other trailers may require a
weight-distributing hitch that uses
spring bars to distribute the trailer
tongue weight between your vehicle
and trailer axles. See

“

Maximum

Trailer Tongue Weight Rating

”

under

Trailer Towing

for weight limits

with various hitch types.

Never attach rental hitches or other
bumper-type hitches. Only use
frame-mounted hitches that do not
attach to the bumper.

Hitch Cover

To remove hitch cover, if equipped:

1. Remove the two fasteners on the

lower tabs (2).

2. Pull the lower edge of the cover

to about a 45 degree angle.

3. Pull the cover upward to

disengage the upper
attachments (1).

«
...
242
243
244
245
246
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: Daihatsu Pages: 340

Brand: Ignition Pages: 1

UNIVERSAL CJ-2A

Brand: Jeep Pages: 27

Brand: Jeep Pages: 228

Brand: Jeep Pages: 108

Brand: Jeep Pages: 525

Brand: Vauxhall Pages: 323

Brand: Bestop Pages: 11

Brand: Whispbar Pages: 14

2014 Insignia VXR SuperSport

Brand: Vauxhall Pages: 56

Brand: AA Products Pages: 4

Brand: PAC Pages: 4

2010 Civic Sedan

Brand: Honda Pages: 390

RUDDER ANGLE INDICATOR

Brand: VDO Pages: 8

Brand: Chevrolet Pages: 372

Brand: Mercedes-Benz Pages: 39

Brand: Quadratec Pages: 12

Brand: Ecco Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands