Cadillac Escalade 2020 Owner'S Manual Download Page 256 | Manualshive

Page: 256 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

256

VEHICLE CARE

1. Positive (+) Terminal. See

.

2.

3. Coolant Surge Tank and Pressure

Cap. See

Cooling System

.

4.

Engine Air Cleaner/Filter

5. Remote Negative (-) Location.

See

Jump Starting

.

6. Engine Cooling Fans (Out of

View). See

Cooling System

7. Engine Oil Fill Cap. See

“

When to

Add Engine Oil

”

under

.

8. Engine Oil Dipstick. See

“

Checking Engine Oil

”

under

.

9. Windshield Washer Fluid

Reservoir. See

“

Adding Washer

Fluid

”

under

.

10. Brake Fluid Reservoir. See

11.

Engine Compartment Fuse Block

.

Engine Oil

To ensure proper engine performance
and long life, careful attention must
be paid to engine oil. Following these
simple, but important steps will help
protect your investment:

.

Use engine oil approved to the
proper specification and of the
proper viscosity grade. See

“

Selecting the Right Engine Oil

”

in

this section.

.

Check the engine oil level regularly
and maintain the proper oil level.
See

“

Checking Engine Oil

”

and

“

When to Add Engine Oil

”

in this

section.

.

Change the engine oil at the
appropriate time. See

.

.

Always dispose of engine oil
properly. See

“

What to Do with

Used Oil

”

in this section.

Checking Engine Oil

If equipped, the ENGINE OIL LOW
ADD OIL message displays when the
engine oil level may be too low. Check

the oil level before filling to the
recommended level. If the oil is not
low and this message remains on, see
your dealer.

Check the engine oil level regularly,
every 650 km (400 mi), especially prior
to a long trip. The engine oil dipstick
handle is a loop. See

Compartment Overview

for the

location.

{

Warning

The engine oil dipstick handle may
be hot; it could burn you. Use a
towel or glove to touch the dipstick
handle.

Follow these guidelines:

.

To get an accurate reading, park
the vehicle on level ground. Check
the engine oil level after the
engine has been off for at least
two hours. Checking the engine oil
level on steep grades or too soon
after engine shutoff can result in
incorrect readings. Accuracy

«
...
254
255
256
257
258
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: B-Speech Pages: 18

Brand: Toyota Pages: 529

Brand: Roav Pages: 10

Brand: Kuda-Phonebase Pages: 3

Brand: Car-Interface Pages: 23

Brand: RuggON Pages: 2

SmartShot Automatic 12V 1.5 Amp 5 Stage

Brand: Yuasa Pages: 44

Brand: Cadillac Pages: 409

Brand: Fortin Pages: 9

Brand: Toyota Pages: 600

Brand: v.LOGiC Pages: 22

Brand: Cadillac Pages: 20

Brand: THIEYE Pages: 88

Brand: Thule Pages: 4

Brand: TAUBENREUTHER Pages: 18

Brand: Toyota Pages: 295

Brand: Ford Pages: 2

Brand: TomTom Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands