Cadillac Escalade 2020 Owner'S Manual Download Page 234 | Manualshive

Page: 234 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

234

DRIVING AND OPERATING

To open the fuel door, push and
release the rearward center edge of
the door.

The capless refueling system does not
have a fuel cap. Fully insert and latch
the fill nozzle, begin fueling.

{

Warning

Overfilling the fuel tank by more
than three clicks of a standard fill
nozzle may cause:

.

Vehicle performance issues,
including engine stalling and
damage to the fuel system.

(Continued)

Warning (Continued)

.

Fuel spills.

.

Under certain conditions, fuel
fires.

Be careful not to spill fuel. Wait
five seconds after you have finished
pumping before removing the fill
nozzle. Clean fuel from painted
surfaces as soon as possible. See

Exterior Care

. Push the fuel door

closed until it latches.

{

Warning

If a fire starts while you are
refueling, do not remove the fill
nozzle. Shut off the flow of fuel by
shutting off the pump or by
notifying the station attendant.
Leave the area immediately.

Filling the Tank with a Portable Fuel
Container

If the vehicle runs out of fuel and
must be filled from a portable fuel
container:

1. Locate the capless funnel

adapter.

2. Insert and latch the funnel into

the capless fuel system.

{

Warning

Attempting to refuel from a
portable fuel container without
using the funnel adapter may cause
fuel spillage and damage the
capless fuel system. This could
cause a fire. You or others could be
badly burned and the vehicle could
be damaged.

«
...
232
233
234
235
236
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: RaceChip Pages: 12

Brand: Vauxhall Pages: 323

Brand: Camcar Pages: 2

LeisureWize EMOVE EM303A

Brand: Streetwize Pages: 20

Brand: BESAFE Pages: 4

Brand: EEZ RV Pages: 31

Brand: ECS Electronics Pages: 16

Brand: Draw tite Pages: 4

Brand: Mercedes-Benz Pages: 329

Brand: GAC MOTOR Pages: 356

Brand: Aries Pages: 5

Brand: Mercedes-Benz Pages: 354

Speed & Route Profiler

Brand: Racelogic Pages: 24

T13 Outback Frontal Protection System

Brand: T.J.M. Pages: 18

Brand: Audi Pages: 4

Brand: Cadillac Pages: 438

Brand: Cadillac Pages: 48

Brand: Ford Pages: 264

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands