Cadillac Escalade 2020 Owner'S Manual Download Page 16

Page: 16 / 355

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

KEYS, DOORS, AND WINDOWS

Use the key in the front doors. The
key cylinder is covered by a cap.
See

“

Driver Door Key Lock

Cylinder Access

”

later in this

section.

Keyless Access

The RKE transmitter must be within
1 m (3 ft) of the liftgate or door being
opened. Press the button on the door
handle to open. See

“

Keyless Access

Operation

”

Remote Keyless Entry

(RKE) System Operation

Driver Door Key Lock Cylinder
Access (Slotted Cap Access) (In
Case of Dead Battery)

To access the driver door key lock
cylinder:

1. Pull the door handle (1) to the

open position and hold it open
until cap removal is complete.

2. Insert the key (4) into the

slot (3) on the bottom of the
cap (2) and lift the key upward.

3. Remove the cap (2).

4. Use the key (4) in the cylinder.

To replace the slotted cap:

1. Pull the door handle (1) to the

open position and hold it open
until cap installation is complete.

Summary of Contents for Escalade 2020




































































































































































































































































































































































Search results

Summary of Contents for Escalade 2020

Reviews:

Related manuals for Escalade 2020

Brands by name

Popular brands

Cadillac Escalade 2020, Owner'S Manual

Search results

Summary of Contents for Escalade 2020

Reviews:

Related manuals for Escalade 2020

Brands by name

Popular brands