Cadillac Escalade 2020 Owner'S Manual Download Page 334

Page: 334 / 355

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

334

SERVICE AND MAINTENANCE

Maintenance Schedule
Additional Required Services -
Severe

000

km/7,500

000

km/15,000

000

km/22,500

000

km/30,000

000

km/37,500

000

km/45,000

000

km/52,500

000

km/60,000

108

000

km/67,500

120

000

km/75,000

132

000

km/82,500

144

000

km/90,000

156

000

km/97,500

168

000

km/105,000

180

000

km/112,500

192

000

km/120,000

204

000

km/127,500

216

000

km/135,000

228

000

km/142,500

240

000

km/150,000

Rotate tires and perform Required Services. Check
engine oil level and oil life percentage. Change
engine oil and filter, if needed.

Replace passenger compartment air filter. (1)

Inspect evaporative control system. (2)

Replace engine air cleaner filter. (3)

Change automatic transmission fluid and filter.

Change transfer case fluid, if equipped with 4WD. (4)

Replace spark plugs. Inspect spark plug wires.

Drain and fill engine cooling system. (5)

Visually inspect accessory drive belts. (6)

Replace brake fluid. (7)

Replace windshield wiper blades. (8)

Replace hood and/or body lift support gas struts. (9)

Replace air conditioning desiccant. (10)

Summary of Contents for Escalade 2020




































































































































































































































































































































































Search results

Summary of Contents for Escalade 2020

Reviews:

Related manuals for Escalade 2020

Brands by name

Popular brands

Cadillac Escalade 2020, Owner'S Manual

Search results

Summary of Contents for Escalade 2020

Reviews:

Related manuals for Escalade 2020

Brands by name

Popular brands