Cadillac Escalade 2020 Owner'S Manual Download Page 74 | Manualshive

Page: 74 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

74

SEATS AND RESTRAINTS

1. Turn the vehicle off.

2. Remove any additional material

from the seat, such as blankets,
cushions, seat covers, seat
heaters, or seat massagers.

3. Place the seatback in the fully

upright position.

4. Have the person sit upright in

the seat, centered on the seat
cushion, with legs comfortably
extended.

5. If the shoulder portion of the

belt is pulled out all the way, the
child restraint locking feature
will be engaged. This may
unintentionally cause the
passenger sensing system to turn
the airbag off for some
adult-sized occupants. If this
happens, unbuckle the belt, let
the belt go back all the way, and
then buckle the belt again
without pulling the belt out all
the way.

6. Restart the vehicle and have the

person remain in this position
for two to three minutes after the
on indicator is lit.

{

Warning

If the front outboard passenger
airbag is turned off for an
adult-sized occupant, the airbag will
not be able to inflate and help
protect that person in a crash,
resulting in an increased risk of
serious injury or even death. An
adult-sized occupant should not
ride in the front outboard passenger
seat, if the passenger airbag off
indicator is lit.

Additional Factors Affecting
System Operation

Seat belts help keep the passenger in
position on the seat during vehicle
maneuvers and braking, which helps
the passenger sensing system
maintain the passenger airbag status.
See

“

Seat Belts

”

and

“

Child Restraints

”

in the Index for additional
information about the importance of
proper restraint use.

A thick layer of additional material,
such as a blanket or cushion,
or aftermarket equipment such as seat
covers, seat heaters, and seat
massagers can affect how well the
passenger sensing system operates.
We recommend that you not use seat
covers or other aftermarket equipment
except when approved by GM for your
specific vehicle. See

Adding Equipment

to the Airbag-Equipped Vehicle

for

more information about modifications
that can affect how the system
operates.

The on indicator may be lit if an
object, such as a briefcase, handbag,
grocery bag, laptop, or other electronic
device, is put on an unoccupied seat.
If this is not desired, remove the
object from the seat.

{

Warning

Stowing articles under the
passenger seat or between the
passenger seat cushion and
seatback may interfere with the
proper operation of the passenger
sensing system.

«
...
72
73
74
75
76
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: KC HiLiTES Pages: 4

Brand: J-Top Pages: 2

Brand: iDataLink Pages: 106

Brand: GARO Pages: 2

PRIME DESIGN VRI3-E-PM11

Brand: Safe Fleet Pages: 12

Brand: Porsche Pages: 192

Brand: Yakima Pages: 19

UCI-11C NTV-KIT331

Brand: Nav TV Pages: 4

Brand: Honda Pages: 208

Brand: EEZ RV Pages: 31

Brand: U & Me Brothers Pages: 6

Stratus LHD 1997

Brand: Chrysler Pages: 1534

Vantage 12 Series

Brand: Ecco Pages: 5

Brand: hc-cargo Pages: 60

2014 Grand Cherokee SRT8

Brand: Jeep Pages: 596

Brand: Skoda Pages: 4

Brand: Whispbar Pages: 15

2005 JR41 Stratus

Brand: Dodge Pages: 293

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands