Cadillac Escalade 2020 Owner'S Manual Download Page 305

Page: 305 / 355

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

VEHICLE CARE

305

7. Tilt the tire toward the vehicle

with some slack in the cable to
access the tire/wheel retainer.

Tilt the retainer and pull it and
the cable and spring through the
center of the wheel.

8. Put the spare tire near the

flat tire.

Removing the Flat Tire and
Installing the Spare Tire

1. Do a safety check before

proceeding. See

If a Tire Goes Flat

301

for more information.

2. If the vehicle has a center cap

that covers the wheel fasteners,
place the chisel end of the wheel
wrench in the slot on the wheel
and gently pry the cap out.

3. Use the wheel wrench to loosen

all the wheel nuts. Turn the
wheel wrench counterclockwise
to loosen the wheel nuts. Do not
remove the wheel nuts yet.

{

Warning

To avoid personal injury and
vehicle damage, disable the power
assist steps before using a jack or
placing an object under the vehicle.
See

Power Assist Steps

Jacking Locations (Overall View)

4. Position the jack under the

vehicle, as shown.

Summary of Contents for Escalade 2020




































































































































































































































































































































































Search results

Summary of Contents for Escalade 2020

Reviews:

Related manuals for Escalade 2020

Brands by name

Popular brands

Cadillac Escalade 2020, Owner'S Manual

Search results

Summary of Contents for Escalade 2020

Reviews:

Related manuals for Escalade 2020

Brands by name

Popular brands