Cadillac Escalade 2020 Owner'S Manual Download Page 21 | Manualshive

Page: 21 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

KEYS, DOORS, AND WINDOWS

21

If the vehicle is shifted out of P (Park)
while the power function is in
progress, the liftgate will continue to
completion. If the vehicle is
accelerated before the liftgate has
completed moving, the liftgate may
stop or reverse direction. Check for
Driver Information Center (DIC)
messages and make sure the liftgate is
closed and latched before driving.

Falling Liftgate Detection

If the power liftgate automatically
closes after a power opening cycle, it
indicates that the system is reacting
to excess weight on the liftgate or a
possible support strut failure.
A repetitive chime will sound while
the falling liftgate detection feature is
operating. Remove any excess weight.
If the liftgate continues to
automatically close after opening, see
your dealer for service before using
the power liftgate.

Interfering with the power liftgate
motion or manually closing the
liftgate too quickly after power
opening may resemble a support strut
failure. This could also activate the
falling liftgate detection feature. Allow

the liftgate to complete its operation
and wait a few seconds before
manually closing the liftgate.

Obstacle Detection Features

If the liftgate encounters an obstacle
during a power open or close cycle,
the liftgate will automatically reverse
direction and move a short distance
away from the obstacle. After
removing the obstruction, the power
liftgate operation can be used again.
If the liftgate encounters multiple
obstacles on the same power cycle,
the power function will deactivate.
After removing the obstructions,
manually close the liftgate. This will
allow normal power operation
functions to resume.

If the vehicle is locked while the
liftgate is closing, and an obstacle is
encountered that prevents the liftgate
from completely closing, the horn will
sound as an alert that the liftgate did
not close.

Pinch sensors are on the side edges of
the liftgate. If an object is caught
between the liftgate and the vehicle
and presses against a sensor, the

liftgate will reverse direction and stop
at a partially open position. The
liftgate will remain open until it is
activated again or closed manually.

Setting the 3/4 Mode

To change the position the liftgate
stops at when opening:

1. Select MAX or 3/4 mode and

power open the liftgate.

2. Stop the liftgate movement at

the desired height by pressing
any liftgate button. Manually
adjust the liftgate position if
needed.

3. Press and hold

l

on the

bottom edge of the liftgate next
to the latch on the outside of the
liftgate until the turn signals
flash and a beep sounds. This
indicates the setting has been
recorded.

The liftgate cannot be set below a
minimum programmable height.
If there is no light flash or sound,
then the height adjustment may be
too low.

«
...
19
20
21
22
23
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: Wagan Pages: 12

Brand: Jabra Pages: 2

Brand: Jabra Pages: 38

Brand: Jeep Pages: 673

Brand: K&M Pages: 3

Brand: Blue Ox Pages: 7

Brand: Shad Pages: 3

Brand: TBC Pages: 12

FIX&GO automatic

Brand: Alfa Romeo Pages: 40

Brand: Warn Pages: 5

Brand: TracRac Pages: 8

Brand: DRAGONFIRE Pages: 4

Brand: EZ-ON Pages: 2

Brand: Toyota Pages: 277

Brand: SAF-HOLLAND Pages: 12

Brand: LAS Pages: 4

Brand: LAS Pages: 24

Brand: Chrysler Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands