Cadillac Escalade 2020 Owner'S Manual Download Page 222 | Manualshive

Page: 222 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

222

DRIVING AND OPERATING

On with Towbar setting allows for
Park Assist to work properly with the
trailer hitch.

Turn off Park Assist and Reverse
Automatic Braking when towing a
trailer.

To turn the RPA symbols, guidance
lines (on some models), or Rear Cross
Traffic Alert on or off, see

“

Rear

Camera

”

and

“

Collision/Detection

Systems

”

under

Vehicle Personalization

. On some models, select the

guidance lines button on the
infotainment display to turn them on
or off.

On some vehicles the RCTA setting
can be turned off through

“

Collision/

Detection Systems

”

under

Personalization

Automatic Parking Assist (APA)

If equipped, APA searches for and
steers the vehicle into parallel and
perpendicular parking spots. When
using APA, you must still shift gears,
and control the brakes and
accelerator. A display and audible
beeps help to guide parking
maneuvers.

{

Warning

APA does not apply the brakes. APA
may not detect objects in the
parking space, objects that are soft
or narrow, objects high off the
ground such as flatbed trucks,
or objects below ground level such
as large potholes. Always verify that
the parking space is appropriate for
parking a vehicle. APA does not
respond to changes in the parking
space, such as movement of an
adjacent vehicle, or a person or
object entering the parking space.
APA does not detect or avoid traffic
that is behind or alongside of the
vehicle. Always be prepared to stop
the vehicle during the parking
maneuver.

Press

O

on the center stack to

enable the system to search for a
parking space that is large enough and
within 1.5 m (5 ft) of the vehicle. The
vehicle speed must be below
30 km/h (18 mph). APA does not work
in 4

m

or 4

n

.

The system cannot:

.

Detect whether it is a legal parking
space.

.

Park exactly lined up with the
vehicle next to it if the spot is
approached at an angle or if the
parking space is angled.

.

Park exactly centered in a spot
that is marked too large.

.

Always detect short curbs.

When enabled, APA searches for
parallel parking spaces to the right of
the vehicle. To search for a parking
space to the left, turn on the left turn
signal or, if available, change the side
selection in the infotainment display.
To switch the parking mode between
parallel and perpendicular, press and
hold

O

during the search process or,

if available, change the parking mode
in the infotainment display.

«
...
220
221
222
223
224
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: Hama Pages: 2

Brand: GMC Pages: 20

Brand: Bestop Pages: 11

Brand: Whispbar Pages: 14

2014 Insignia VXR SuperSport

Brand: Vauxhall Pages: 56

Stratus LHD 1997

Brand: Chrysler Pages: 1534

Brand: Warn Pages: 5

RVS systems RVS-M641

Brand: Safe Fleet Pages: 24

Brand: Thule Pages: 4

Brand: Pogo Pages: 40

Brand: Edelbrock Pages: 2

Brand: Hudson Pages: 77

Brand: Curt Group Pages: 3

Brand: Juna Pages: 10

Brand: BMW Pages: 64

Hitch-Haul 30110315

Brand: Masterbuilt Pages: 2

Brand: Kargo Master Pages: 8

Brand: XTC Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands