manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

326

VEHICLE CARE

Do not use cleaners that increase
gloss, especially on the instrument
panel. Reflected glare can decrease
visibility through the windshield
under certain conditions.

Caution

Use of air fresheners may cause
permanent damage to plastics and
painted surfaces. If an air freshener
comes in contact with any plastic
or painted surface in the vehicle,
blot immediately and clean with a
soft cloth dampened with a mild
soap solution. Damage caused by
air fresheners would not be covered
by the vehicle warranty.

Cargo Cover and
Convenience Net

If equipped, wash with warm water
and mild detergent. Do not use
chlorine bleach. Rinse with cold water,
and then dry completely.

Care of Seat Belts

Keep belts clean and dry.

{

Warning

Do not bleach or dye seat belt
webbing. It may severely weaken
the webbing. In a crash, they might
not be able to provide adequate
protection. Clean and rinse seat belt
webbing only with mild soap and
lukewarm water. Allow the webbing
to dry.

Floor Mats

{

Warning

If a floor mat is the wrong size or is
not properly installed, it can
interfere with the pedals.
Interference with the pedals can
cause unintended acceleration and/
or increased stopping distance
which can cause a crash and injury.
Make sure the floor mat does not
interfere with the pedals.

Use the following guidelines for
proper floor mat usage:

.

The original equipment floor mats
were designed for your vehicle.
If the floor mats need replacing, it
is recommended that GM certified
floor mats be purchased. Non-GM
floor mats may not fit properly
and may interfere with the pedals.
Always check that the floor mats
do not interfere with the pedals.

.

Do not use a floor mat if the
vehicle is not equipped with a
floor mat retainer on the driver
side floor.

.

Use the floor mat with the correct
side up. Do not turn it over.

.

Do not place anything on top of
the driver side floor mat.

.

Use only a single floor mat on the
driver side.

.

Do not place one floor mat on top
of another.

Removing and Replacing the
Floor Mats

Pull up on the rear of the floor mat to
unlock each retainer and remove.

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

TATA Motors Nano Owner'S Manual & Service Book preview
Nano
Brand: TATA Motors Pages: 94
GÄN GA Manual preview
GA
Brand: GÄN Pages: 24
Hama Neptun Manual preview
Neptun
Brand: Hama Pages: 6
Jacob Jensen Electronic Parking Disc 3 Quick Manual preview
Electronic Parking Disc 3
Brand: Jacob Jensen Pages: 2
Yakima K1005 Instructions Manual preview
K1005
Brand: Yakima Pages: 12
Suzuki Movano Owner'S Manual preview
Movano
Brand: Suzuki Pages: 353
Torklift F2012 Installation Instructions Manual preview
F2012
Brand: Torklift Pages: 16
Alpine eX-10 Installation Manual preview
eX-10
Brand: Alpine Pages: 8
U & Me Brothers LK-168A Manual preview
LK-168A
Brand: U & Me Brothers Pages: 6
CITROËN C4 CACTUS Handbook preview
C4 CACTUS
Brand: CITROËN Pages: 301
Camoplast Polaris TATOU 4S Installation Manuallines preview
Polaris TATOU 4S
Brand: Camoplast Pages: 13
Safe Fleet inView 360 Fusion Calibration Manual preview
inView 360 Fusion
Brand: Safe Fleet Pages: 27
Seat ROADSIDE ASSISTANCE Handbook preview
ROADSIDE ASSISTANCE
Brand: Seat Pages: 44
AEM 30-3500 Instruction Manual preview
30-3500
Brand: AEM Pages: 27
Flash Cover MN019 Instructions preview
MN019
Brand: Flash Cover Pages: 2
Porsche WTY 2010 Warranty & Maintenance Manual preview
WTY 2010
Brand: Porsche Pages: 98
Unex OBU-352EC Quick Start Manual preview
OBU-352EC
Brand: Unex Pages: 30
Acura 08L07-TA1-203 Installation Instructions Manual preview
08L07-TA1-203
Brand: Acura Pages: 6

Brands by name

Popular brands

Load more brands