manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

196

DRIVING AND OPERATING

automatically based on driving
conditions. This setting provides
slightly lower fuel economy than 2

m

.

Do not use AUTO mode, if equipped,
to park on a steep grade with poor
traction such as ice, snow, mud,
or gravel. In AUTO mode only the rear
wheels will hold the vehicle from
sliding when parked. If parking on a
steep grade, use 4

m

to keep all four

wheels engaged.

4

m

(Four-Wheel Drive High) :

Use

this position when extra traction is
needed, such as when driving on
snowy or icy roads, when off-roading,
or when plowing snow.

4

n

(Four-Wheel Drive Low) :

This

setting engages the front axle and
delivers extra torque. Choose 4

n

when

driving off-road in deep sand, deep
mud, or deep snow, and while
climbing or descending steep hills.

Shifting into 4

n

will turn Traction

Control and StabiliTrak off. See

Traction Control/Electronic Stability
Control

0

201

.

Shifting Into 4

m

or AUTO

Turn the knob to the 4

m

or AUTO

position at any speed, except from 4

n

.

The indicator light will flash while
shifting and will remain on when the
shift is completed.

Shifting Into 2

m

Turn the knob to 2

m

at any speed,

except when shifting from 4

n

. The

indicator light will flash while shifting
and will remain on when the shift is
completed.

Shifting Into 4

n

When 4

n

is engaged, keep vehicle

speed below 72 km/h (45 mph).

To shift:

1. The ignition must be on and the

vehicle must be stopped or
moving less than 5 km/h (3 mph)

with the transmission in
N (Neutral). It is best for the
vehicle to be moving
1.6 to 3.2 km/h (1 to 2 mph).

2. Turn the knob to 4

n

. Wait for

the 4

n

indicator light to stop

flashing before shifting the
transmission into gear.

Caution

Shifting the transmission into gear
before the requested mode indicator
light has stopped flashing could
damage the transfer case.

If the transmission is in gear and/or
moving more than 5 km/h (3 mph), the
4

n

indicator light will flash for

30 seconds and not complete the shift.
After 30 seconds the transfer case will
shift to 4

m

. Turn the knob to 4

m

to

display the indicator. With the vehicle
moving less than 5 km/h (3 mph), and
the transmission in N (Neutral),
attempt the shift again.

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Calira 811 Manual preview
811
Brand: Calira Pages: 14
Metra Electronics 99-3010S Installation Instructions Manual preview
99-3010S
Brand: Metra Electronics Pages: 14
RaceChip Pro 2 Installation Manual preview
Pro 2
Brand: RaceChip Pages: 12
Hama 00201510 Operating Instructions Manual preview
00201510
Brand: Hama Pages: 40
UAZ UAZ-374195 Operating Manual preview
UAZ-374195
Brand: UAZ Pages: 90
Mercedes-Benz Sprinter 2003 Manual preview
Sprinter 2003
Brand: Mercedes-Benz Pages: 296
ECS FIA-030-B Fitting Instructions preview
FIA-030-B
Brand: ECS Pages: 4
Whispbar WB751 Manual preview
WB751
Brand: Whispbar Pages: 15
Metra Electronics 99-9302 Installation Instructions Manual preview
99-9302
Brand: Metra Electronics Pages: 8
Prime Design FEA-0004 Assembly Instructions Manual preview
FEA-0004
Brand: Prime Design Pages: 12
Front Runner LATF002 Quick Start Manual preview
LATF002
Brand: Front Runner Pages: 7
Mazda Auto-Dimming Mirror User Manual preview
Auto-Dimming Mirror
Brand: Mazda Pages: 2
Porsche 1972 911 Workshop Manual preview
1972 911
Brand: Porsche Pages: 1005
Audiovox Auto Security AA-9103N Installation Manual preview
Auto Security AA-9103N
Brand: Audiovox Pages: 1
SkyRack SR-CB-101 Assembly And Instruction Sheet preview
SR-CB-101
Brand: SkyRack Pages: 2
Honda 2002 Civic Hatchback Service Manual preview
2002 Civic Hatchback
Brand: Honda Pages: 119
SAN HIMA ROOF-RACK-T User Manual preview
ROOF-RACK-T
Brand: SAN HIMA Pages: 8
Volkswagen RCD550 Installation Manual preview
RCD550
Brand: Volkswagen Pages: 4

Brands by name

Popular brands

Load more brands