Cadillac Escalade 2020 Owner'S Manual Download Page 318 | Manualshive

Page: 318 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

318

VEHICLE CARE

Caution

Failure to disconnect the negative
battery cable or to have it contact
the terminals can cause damage to
the vehicle.

6. Disconnect the negative battery

cable at the battery and secure
the nut and bolt. Cover the
negative battery post with a
non-conductive material to
prevent any contact with the
negative battery terminal.

7. Shift the transmission to

P (Park).

Caution

If the steering column is locked,
vehicle damage may occur.

8. Move the steering wheel to make

sure the steering column is
unlocked.

9. With a foot on the brake pedal,

release the parking brake.

10. If equipped with Keyless Access,

keep the RKE transmitter outside
of the vehicle, and manually lock
the doors. Access the vehicle as
if it has a dead RKE transmitter
battery, by using the key in the
door lock.

Disconnecting the Towed Vehicle

Before disconnecting the towed
vehicle:

1. Park on a level surface.

2. Set the parking brake, then shift

the transmission to P (Park).

3. Connect the battery.

4. Apply the brake pedal.

5. Turn the ignition on with the

engine off. Shift the transfer case
out of N (Neutral) to 2

m

. See

“

Shifting out of N (Neutral)

”

under

Four-Wheel Drive

See your dealer if the transfer
case cannot be shifted out of
N (Neutral).

6. Check that the vehicle is in 2

m

by starting the engine and
shifting the transmission to

R (Reverse) and then to D
(Drive). There should be
movement of the vehicle while
shifting.

7. Shift the transmission to P (Park)

and turn off the ignition.

8. Disconnect the vehicle from the

tow vehicle.

9. Release the parking brake.

10. Reset any lost presets.

The outside temperature display
will default to 0 °C (32 °F) but
will reset with normal usage.

Dolly Towing

«
...
316
317
318
319
320
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: Kathrein Pages: 7

Brand: RAM Pages: 292

Brand: RAM Pages: 116

Brand: UMBRA RIMORCHI Pages: 18

Brand: Carefree Pages: 12

2005 Sierra Denali

Brand: GMC Pages: 428

Brand: Mercedes-Benz Pages: 346

Brand: Thule Pages: 4

Brand: Whispbar Pages: 15

Wireless Handsfree Car Kit

Brand: Wagan Pages: 20

Brand: Metra Electronics Pages: 20

Brand: Whipple Pages: 3

Brand: Nav TV Pages: 4

Brand: Jeep Pages: 136

Brand: Hama Pages: 4

Brand: Volvo Pages: 230

Prime Design OCM-3032

Brand: Safe Fleet Pages: 4

Brand: MMD Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands