Cadillac Escalade 2020 Owner'S Manual Download Page 224 | Manualshive

Page: 224 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

224

DRIVING AND OPERATING

Alert (LCA), and/or Automatic
Emergency Braking (AEB) can help to
avoid a crash or reduce crash damage.

Forward Collision Alert
(FCA) System

If equipped, the FCA system may help
to avoid or reduce the harm caused by
front-end crashes. When approaching
a vehicle ahead too quickly, FCA
provides a red flashing alert on the
windshield and rapidly beeps or pulses
the driver seat. FCA also lights an
amber visual alert if following another
vehicle much too closely.

FCA detects vehicles within a distance
of approximately 60 m (197 ft) and
operates at speeds above 8 km/h
(5 mph). If the vehicle has Adaptive
Cruise Control (ACC), it can detect
vehicles to distances of approximately
110 m (360 ft) and operates at all
speeds. See

Adaptive Cruise Control

.

{

Warning

FCA is a warning system and does
not apply the brakes. When
approaching a slower-moving or
stopped vehicle ahead too rapidly,
or when following a vehicle too
closely, FCA may not provide a
warning with enough time to help
avoid a crash. It also may not
provide any warning at all. FCA
does not warn of pedestrians,
animals, signs, guardrails, bridges,
construction barrels, or other
objects. Be ready to take action and
apply the brakes. See

.

FCA can be disabled with either the
FCA steering wheel control or,
if equipped, through vehicle
personalization. See

“

Collision/

Detection Systems

”

under

Personalization

.

Detecting the Vehicle Ahead

FCA warnings will not occur unless
the FCA system detects a vehicle
ahead. When a vehicle is detected, the
vehicle ahead indicator will display
green. Vehicles may not be detected
on curves, highway exit ramps,
or hills, due to poor visibility; or if a
vehicle ahead is partially blocked by
pedestrians or other objects. FCA will
not detect another vehicle ahead until
it is completely in the driving lane.

{

Warning

FCA does not provide a warning to
help avoid a crash, unless it detects
a vehicle. FCA may not detect a
vehicle ahead if the FCA sensor is
blocked by dirt, snow, or ice, or if

(Continued)

«
...
222
223
224
225
226
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: Laser Pages: 8

Brand: Metra Electronics Pages: 2

Brand: Tessera4x4 Pages: 20

PRIME DESIGN VRR-NV200

Brand: Safe Fleet Pages: 12

Brand: Parkeon Pages: 43

Impala Limited 2014

Brand: Chevrolet Pages: 356

Brand: iOttie Pages: 58

Park Vision VAL632210

Brand: Valeo Pages: 25

Brand: S3 Power Sports Pages: 2

2004 Impreza OUTBACK SPORT

Brand: Subaru Pages: 34

Brand: Thule Pages: 4

Brand: Horn Tools Pages: 12

Brand: Ford Pages: 40

2000 9-5 2.3 Turbo Ecopower

Brand: Saab Pages: 256

Brand: RAM Pages: 666

PerfectView LCD350

Brand: Waeco Pages: 36

Brand: Ford Pages: 256

Brand: VP Autoparts Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands