Cadillac Escalade 2020 Owner'S Manual Download Page 171 | Manualshive

Page: 171 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

DRIVING AND OPERATING

171

For more information about loading
the vehicle, see

Vehicle Load Limits

and

Environmental Concerns

.

Always use established trails,
roads, and areas that have been
set aside for public off-road
recreational driving and obey all
posted regulations.

.

Do not damage shrubs, flowers,
trees, or grasses or disturb wildlife.

.

Do not park over things that burn.
See

Parking over Things That Burn

Driving on Hills

Driving safely on hills requires good
judgment and an understanding of
what the vehicle can and cannot do.

{

Warning

Many hills are simply too steep for
any vehicle. Driving up hills can
cause the vehicle to stall. Driving

(Continued)

Warning (Continued)

down hills can cause loss of control.
Driving across hills can cause a
rollover. You could be injured or
killed. Do not drive on steep hills.

Before driving on a hill, assess the
steepness, traction, and obstructions.
If the terrain ahead cannot be seen,
get out of the vehicle and walk the hill
before driving further.

When driving on hills:

.

Use a low gear and keep a firm
grip on the steering wheel.

.

Maintain a slow speed.

.

When possible, drive straight up
or down the hill.

.

Slow down when approaching the
top of the hill.

.

Use headlamps even during the
day to make the vehicle more
visible.

{

Warning

Driving to the top of a hill at high
speed can cause a crash. There
could be a drop-off, embankment,
cliff, or even another vehicle. You
could be seriously injured or killed.
As you near the top of a hill, slow
down and stay alert.

.

Never go downhill forward or
backward with either the
transmission or transfer case in
N (Neutral). The brakes could
overheat and you could lose
control.

{

Warning

If the vehicle has the two-speed
automatic or electronic transfer
case, shifting the transfer case to
N (Neutral) can cause your vehicle
to roll even if the transmission is in
P (Park). This is because the
N (Neutral) position on the transfer

(Continued)

«
...
169
170
171
172
173
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: Panasonic Pages: 2

CYRC50U - UNIVERSAL REAR-VIEW CAMERA

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 12

Brand: Lincoln Pages: 424

Brand: Volkswagen Pages: 26

Brand: Kia Pages: 419

Brand: Ford Pages: 2

Brand: Nav TV Pages: 5

Ram Commercial2016

Brand: Dodge Pages: 675

Brand: CALIMA Pages: 9

Brand: Honda Pages: 20

2009 Rio Series

Brand: Kia Pages: 219

Brand: Pacbrake Pages: 6

BEDXTENDER HD MAX 74841-00A

Brand: AMP Research Pages: 9

Brand: Belkin Pages: 2

FOLDING TOP 1971

Brand: Fisher Body Pages: 37

Brand: Manik Pages: 2

Brand: E&G Classics Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands