Cadillac Escalade 2020 Owner'S Manual Download Page 177 | Manualshive

Page: 177 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

DRIVING AND OPERATING

177

If the Vehicle Is Stuck

Slowly and cautiously spin the wheels
to free the vehicle when stuck in sand,
mud, ice, or snow. See

“

Rocking the

Vehicle to Get It Out

”

later in this

section.

The Traction Control System (TCS)
can often help to free a stuck vehicle.
See

Traction Control/Electronic Stability

. If TCS cannot free the

vehicle, see

“

Rocking the Vehicle to

Get it Out

”

following.

{

Warning

If the vehicle's tires spin at high
speed, they can explode, and you or
others could be injured. The vehicle
can overheat, causing an engine
compartment fire or other damage.
Spin the wheels as little as possible
and avoid going above 56 km/h
(35 mph).

For information about using tire
chains on the vehicle, see

.

Rocking the Vehicle to Get It Out

Turn the steering wheel left and right
to clear the area around the front
wheels. For four-wheel-drive vehicles,
shift into Four-Wheel Drive High.
Turn the TCS off. Shift back and forth
between R (Reverse) and a forward
gear, spinning the wheels as little as
possible. To prevent transmission
wear, wait until the wheels stop
spinning before shifting gears. Slowly
spinning the wheels in the forward
and reverse directions causes a
rocking motion that could free the
vehicle. If that does not get the
vehicle out after a few tries, it might
need to be towed out. See

.

Vehicle Load Limits

It is very important to know how
much weight the vehicle can carry.
This weight is called the vehicle
capacity weight and includes the
weight of all occupants, cargo, and
all nonfactory-installed options.
Two labels on the vehicle may
show how much weight it was

designed to carry, the Tire and
Loading Information label and the
Certification/Tire label.

{

Warning

Do not load the vehicle any
heavier than the Gross Vehicle
Weight Rating (GVWR),
or either the maximum front or
rear Gross Axle Weight Rating
(GAWR). This can cause
systems to break and change
the way the vehicle handles.
This could cause loss of control
and a crash. Overloading can
also reduce stopping distance,
damage the tires, and shorten
the life of the vehicle.

«
...
175
176
177
178
179
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: Ford Pages: 12

Brand: Vintage Air Pages: 28

Brand: Sirius Satellite Radio Pages: 8

FIX&GO automatic

Brand: Alfa Romeo Pages: 40

Brand: Gatorback Mudflaps Pages: 4

MCL-7000 Series

Brand: Dakota Digital Pages: 2

Brand: Volvo Pages: 284

Brand: Hella Pages: 21

Brand: Vauxhall Pages: 259

Brand: Thule Pages: 12

2917 Nstallation

Brand: Edelbrock Pages: 1

Brand: Lantronix Pages: 51

EQ forfour 2018

Brand: SMART Pages: 224

Brand: Genesis Pages: 29

Brand: Rajant Pages: 11

2018 GRAND CHEROKEE

Brand: Jeep Pages: 372

Brand: American muscle Pages: 3

Brand: CAME Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands