manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

DRIVING AND OPERATING

205

Operating the vehicle in Tow/Haul
when lightly loaded or with no trailer
at all will not cause damage. However,
there is no benefit to the selection of
Tow/Haul when the vehicle is
unloaded. Such a selection when
unloaded may result in unpleasant
engine and transmission driving
characteristics and reduced fuel
economy. Tow/Haul is recommended
only when pulling a heavy trailer or a
large or heavy load.

When selected, the Tow/Haul
indicator will display in the
instrument cluster.

Magnetic Ride Control

This vehicle may have a semi-active
damping system called Magnetic Ride
Control. With this feature, improved
vehicle ride and handling is provided
under a variety of passenger and
loading conditions.

Locking Rear Axle

Vehicles with a locking rear axle can
give more traction on snow, mud, ice,
sand, or gravel. It works like a

standard axle most of the time, but
when traction is low, this feature will
allow the rear wheel with the most
traction to move the vehicle.

Automatic Level Control

The automatic level control rear
suspension comes as a part of the
Magnetic Ride Control system.

This type of level control is fully
automatic and will provide a better
leveled riding position as well as
better handling under a variety of
passenger and loading conditions. An
air compressor connected to the rear
shocks will raise or lower the rear of
the vehicle to maintain proper vehicle
height. The system is activated when
the ignition is on and will
automatically adjust vehicle height
thereafter. The system may exhaust
(lower vehicle height) for up to
10 minutes after the ignition has been
turned off. You may hear the air
compressor operating when the height
is being adjusted.

If a weight-distributing hitch is being
used, it is recommended to allow the
shocks to inflate, leveling the vehicle
prior to adjusting the hitch.

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Kargo Master 40640 Assembly Manual preview
40640
Brand: Kargo Master Pages: 5
RAM 2015 1500 User Manual preview
2015 1500
Brand: RAM Pages: 292
RAM Trucks 1500 User Manual preview
Trucks 1500
Brand: RAM Pages: 116
Porsche Carrera GT Manual preview
Carrera GT
Brand: Porsche Pages: 192
AMP Research 75135-01A Installation Manual preview
75135-01A
Brand: AMP Research Pages: 12
Havis-Shields Half Size Trunk Box Organizer C-TBO-CV Installation Instructions preview
Half Size Trunk Box Organizer C-TBO-CV
Brand: Havis-Shields Pages: 1
Volvo S60 2012 Quick Manual preview
S60 2012
Brand: Volvo Pages: 8
Alfa Romeo FIX&GO automatic Manual preview
FIX&GO automatic
Brand: Alfa Romeo Pages: 40
Kia Sorento Owner'S Manual preview
Sorento
Brand: Kia Pages: 51
STARLANE POLE STAR PRO Installation And Instruction Manual preview
POLE STAR PRO
Brand: STARLANE Pages: 24
Safe Fleet Prime Design VBI-FT31B Assembly Instructions Manual preview
Prime Design VBI-FT31B
Brand: Safe Fleet Pages: 12
Vauxhall 2013 Ampera Infotainment Manual preview
2013 Ampera
Brand: Vauxhall Pages: 95
RAM Cargo Van 2014 Owner'S Manual preview
Cargo Van 2014
Brand: RAM Pages: 666
Waeco PerfectView LCD350 Installation And Operating Manual preview
PerfectView LCD350
Brand: Waeco Pages: 36
Curt Group 60638 Installation Manual preview
60638
Brand: Curt Group Pages: 3
Juna JRDAB-03 Installation Manual preview
JRDAB-03
Brand: Juna Pages: 10
VDO ELECTRONIC SPEEDOMETER 1323 Datasheet preview
ELECTRONIC SPEEDOMETER 1323
Brand: VDO Pages: 2
NavInc USB-PEU-RD4 User Manual preview
USB-PEU-RD4
Brand: NavInc Pages: 5

Brands by name

Popular brands

Load more brands