manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

DRIVING AND OPERATING

231

How the System Works

LKA uses a camera sensor installed on
the windshield ahead of the rearview
mirror to detect lane markings. It may
provide brief steering assist if it
detects an unintended lane departure.
It may further provide an audible alert
or the driver seat may pulse indicating
that a lane marking has been crossed.

To turn LKA on and off, press

A

on the center stack. If equipped, the
indicator light on the button comes
on when LKA is on and turns off
when LKA is disabled.

When on,

A

is white, if equipped,

indicating that the system is not ready
to assist.

A

is green if LKA is ready

to assist. LKA may assist by gently
turning the steering wheel if the
vehicle approaches a detected lane
marking.

A

is amber when

assisting. It may also provide a Lane
Departure Warning (LDW) alert by
flashing

A

amber if the vehicle

crosses a detected lane marking.
Additionally, there may be three
beeps, or the driver seat may pulse

three times, on the right or left,
depending on the lane departure
direction.

Take Steering

The LKA system does not
continuously steer the vehicle. If LKA
does not detect active driver steering,
an alert and chime may be provided.
Steer the vehicle to dismiss. LKA may
become temporarily unavailable after
repeated take steering alerts.

When the System Does Not
Seem to Work Properly

The system performance may be
affected by:

.

Close vehicles ahead.

.

Sudden lighting changes, such as
when driving through tunnels.

.

Banked roads.

.

Roads with poor lane markings,
such as two-lane roads.

A system unavailable message may
display if the camera is blocked. The
LKA system does not need service.

A camera blocked message may
display if the camera is blocked. Some
driver assistance systems may have
reduced performance or not work at
all. An LKA or LDW unavailable
message may display if the systems
are temporarily unavailable. This
message could be due to a blocked
camera. The LKA system does not
need service. Clean the outside of the
windshield behind the rearview mirror.

LKA assistance and/or LDW alerts
may occur due to tar marks, shadows,
cracks in the road, temporary or
construction lane markings, or other
road imperfections. This is normal
system operation; the vehicle does not
need service. Turn LKA off if these
conditions continue.

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Federal Signal Corporation 7000 Assembly Instructions Manual preview
7000
Brand: Federal Signal Corporation Pages: 13
HALE MM-03 Driver Manual preview
MM-03
Brand: HALE Pages: 44
Napoli NPL-TV 7874 DIGITAL Instruction Manual preview
NPL-TV 7874 DIGITAL
Brand: Napoli Pages: 20
Blue Ox BX3781 Installation Instructions Manual preview
BX3781
Brand: Blue Ox Pages: 7
Shad NADSA ATV80 Owner'S Manual preview
NADSA ATV80
Brand: Shad Pages: 3
Wagan Wireless Handsfree Car Kit User Manual preview
Wireless Handsfree Car Kit
Brand: Wagan Pages: 20
Safe Fleet PRIME DESIGN VRR-NV200 Manual preview
PRIME DESIGN VRR-NV200
Brand: Safe Fleet Pages: 12
Honda 08A06-361-210 Installation Instructions preview
08A06-361-210
Brand: Honda Pages: 4
Pro-gard SAFESTOP SS0005 Installation Manual preview
SAFESTOP SS0005
Brand: Pro-gard Pages: 4
Ford 2005 P207 Explorer Sport Trac Owner'S Manual preview
2005 P207 Explorer Sport Trac
Brand: Ford Pages: 540
I.D. Systems Vehicle Asset Communicator User Manual preview
Vehicle Asset Communicator
Brand: I.D. Systems Pages: 41
APS IA06SJD4B Installation Instructions preview
IA06SJD4B
Brand: APS Pages: 3
Mazda 2010 MX-5 Miata Specification preview
2010 MX-5 Miata
Brand: Mazda Pages: 8
Toyota RAV-4 2015 Series Owner'S Manual Supplement preview
RAV-4 2015 Series
Brand: Toyota Pages: 50
Oldsmobile 2003 Silhouette Owner'S Manual preview
2003 Silhouette
Brand: Oldsmobile Pages: 466
Mitsubishi Fuso FK 2010 Owner'S Manual preview
Fuso FK 2010
Brand: Mitsubishi Pages: 362
Toyota Solara guide Owner'S Manual preview
Solara guide
Brand: Toyota Pages: 497
Volvo 30795637 User Manual preview
30795637
Brand: Volvo Pages: 92

Brands by name

Popular brands

Load more brands