manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

SEATS AND RESTRAINTS

61

Push down on the release button to
move the height adjuster to the
desired position.

Move the adjuster up by pushing up
on the shoulder belt guide.

After the adjuster is set to the desired
position, try to move it down without
pushing the release button to make
sure it has locked into position.

Automatic Seat Belt Tightening
System

The vehicle may have the Automatic
Seat Belt Tightening System.

The system activates during
emergency braking and/or sudden
driving maneuvers and releases when
driving conditions return to normal.

The system will not activate if the
Traction Control/Electronic Stability
Control system is not functioning
properly. See

Traction Control/

Electronic Stability Control

0

201

.

If there is a problem with the
Automatic Seat Belt Tightening
System, a message displays on the
Driver Information Center (DIC). If a
system unavailable message displays
repeatedly or a service message
displays, see your dealer. Other seat
belt functions are not affected by the
Automatic Seat Belt Tightening
System.

Seat Belt Pretensioners

This vehicle has seat belt
pretensioners for the front outboard
occupants. Although the seat belt
pretensioners cannot be seen, they are
part of the seat belt assembly. They
can help tighten the seat belts during
the early stages of a moderate to
severe frontal, near frontal, or rear

crash if the threshold conditions for
pretensioner activation are met. Seat
belt pretensioners can also help
tighten the seat belts in a side crash
or a rollover event.

Pretensioners work only once. If the
pretensioners activate in a crash, the
pretensioners and probably other
parts of the vehicle's seat belt system
will need to be replaced. See

Replacing

Seat Belt System Parts after a Crash

0

64

.

Do not sit on the outboard seat belt
while entering or exiting the vehicle or
at any time while sitting in the seat.
Sitting on the seat belt can damage
the webbing and hardware.

Rear Seat Belt Comfort Guides

{

Warning

A seat belt that is not properly
worn may not provide the
protection needed in a crash. The
person wearing the belt could be
seriously injured. The shoulder belt

(Continued)

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Camoplast T4S User Manual preview
T4S
Brand: Camoplast Pages: 60
Toyota 2012 Rav4 Owner'S Manual preview
2012 Rav4
Brand: Toyota Pages: 529
Wilco Offroad UHG2060/AU Installation Manual preview
UHG2060/AU
Brand: Wilco Offroad Pages: 4
Thule Kit 2161 Fitting Instructions preview
Kit 2161
Brand: Thule Pages: 2
Park-Daddy PD50AA Installation Manual preview
PD50AA
Brand: Park-Daddy Pages: 22
Havis-Shields 1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P Datasheet preview
1996-2008 Crown Victoria Driver and Passenger - Trunk Side Mounts C-TSM-CV-P
Brand: Havis-Shields Pages: 1
C-KO RS-4-18-R-I Fitting Instructions preview
RS-4-18-R-I
Brand: C-KO Pages: 4
National Cycle Quantum Wash'n'Wipe N30208 Assembly Instructions And Owner'S Manual preview
Quantum Wash'n'Wipe N30208
Brand: National Cycle Pages: 12
AL-KO AKS 1300 Operating Instructions Manual preview
AKS 1300
Brand: AL-KO Pages: 40
Mont Blanc ACTIVA+ Assembly Instructions preview
ACTIVA+
Brand: Mont Blanc Pages: 2
Horn Tools HJIMRR02FIT Mounting Instructions preview
HJIMRR02FIT
Brand: Horn Tools Pages: 12
Master Tailgaters MR-43E2DVR1 User Manual preview
MR-43E2DVR1
Brand: Master Tailgaters Pages: 10
Hyundai 2001 Elantra Owner'S Manual preview
2001 Elantra
Brand: Hyundai Pages: 168
Genesis GV60 2022 Quick Reference Manual preview
GV60 2022
Brand: Genesis Pages: 29
Hamron 012463 Operating Instructions Manual preview
012463
Brand: Hamron Pages: 6
Rally Armor IMF63 Installation Instruction preview
IMF63
Brand: Rally Armor Pages: 4
Fortin Electronic Systems EVO-CAN Suggested Wiring Configuration preview
EVO-CAN
Brand: Fortin Electronic Systems Pages: 5
Chevrolet CORVETTE 2020 Owner'S Manual preview
CORVETTE 2020
Brand: Chevrolet Pages: 324

Brands by name

Popular brands

Load more brands