Cadillac Escalade 2020 Owner'S Manual Download Page 121 | Manualshive

Page: 121 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

INSTRUMENTS AND CONTROLS

121

Malfunctions are often indicated by
the system before any problem is
noticeable. Being aware of the light
and seeking service promptly when it
comes on may prevent damage.

Caution

If the vehicle is driven continually
with this light on, the emission
control system may not work as
well, the fuel economy may be
lower, and the vehicle may not run
smoothly. This could lead to costly
repairs that might not be covered
by the vehicle warranty.

Caution

Modifications to the engine,
transmission, exhaust, intake,
or fuel system, or the use of
replacement tires that do not meet
the original tire specifications, can
cause this light to come on. This
could lead to costly repairs not
covered by the vehicle warranty.
This could also affect the vehicle

’

s

ability to pass an Emissions
Inspection/Maintenance test. See

Accessories and Modifications

.

If the light is flashing :

A

malfunction has been detected that
could damage the emission control
system and increase vehicle
emissions. Diagnosis and service may
be required.

To help prevent damage, reduce
vehicle speed and avoid hard
accelerations and uphill grades.
If towing a trailer, reduce the amount
of cargo being hauled as soon as
possible.

If the light continues to flash, find a
safe place to park. Turn the vehicle off
and wait at least 10 seconds before
restarting the engine. If the light is
still flashing, follow the previous
guidelines and see your dealer for
service as soon as possible.

If the light is on steady :

A

malfunction has been detected.
Diagnosis and service may be
required.

Check the following:

.

If fuel has been added to the
vehicle using the capless fuel
funnel adapter, make sure that it
has been removed. See

“

Filling the

Tank with a Portable Gas Can

”

under

Filling the Tank

. The

diagnostic system can detect if the
adapter has been left installed in
the vehicle, allowing fuel to
evaporate into the atmosphere.
A few driving trips with the
adapter removed may turn off the
light.

.

Poor fuel quality can cause
inefficient engine operation and
poor driveability, which may go

«
...
119
120
121
122
123
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: Warrior Products Pages: 4

Brand: Jeep Pages: 380

Brand: Hummer Pages: 502

Brand: Toyota Pages: 636

XEBRA ZAPCAR Series

Brand: Zap Pages: 16

Brand: v.link Pages: 12

Brand: Rugged Ridge Pages: 2

Brand: Mobridge Pages: 20

Brand: Edelbrock Pages: 2

Brand: Mitsubishi Pages: 367

Brand: Meritor Pages: 20

SB-J-GCHER2/10W3v2

Brand: Stealthbox Pages: 2

Brand: Kuda-Phonebase Pages: 3

Brand: Kuda Pages: 3

Brand: Ranger design Pages: 22

Brand: AUTOTECH Pages: 2

Brand: Connects2 Pages: 2

Brand: Wabtec Pages: 216

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands