manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

120

INSTRUMENTS AND CONTROLS

When the vehicle is started, the
passenger airbag status indicator will
light the symbols for on and off for
several seconds as a system check.
Then, after several more seconds, the
status indicator will light either the on
or off symbol to let you know the
status of the front outboard passenger
frontal airbag.

If the on symbol is lit on the
passenger airbag status indicator, it
means that the front outboard
passenger frontal airbag is allowed to
inflate.

If the off symbol is lit on the airbag
status indicator, it means that the
passenger sensing system has turned
off the front outboard passenger
frontal airbag.

If, after several seconds, both status
indicator lights remain on, or if there
are no lights at all, there may be a

problem with the lights or the
passenger sensing system. See your
dealer for service.

{

Warning

If the airbag readiness light ever
comes on and stays on, it means
that something may be wrong with
the airbag system. To help avoid
injury to yourself or others, have
the vehicle serviced right away. See

Airbag Readiness Light

0

119

for

more information, including
important safety information.

Charging System Light

The charging system light comes on
briefly when the ignition is turned on,
but the engine is not running, as a

check to show the light is working.
It should go out when the engine is
started.

If the light stays on, or comes on
while driving, there may be a problem
with the electrical charging system.
Have it checked by your dealer.
Driving while this light is on could
drain the battery.

When this light comes on, or is
flashing, the Driver Information
Center (DIC) also displays a message.

If a short distance must be driven
with the light on, be sure to turn off
all accessories, such as the radio and
air conditioner.

Malfunction Indicator Lamp
(Check Engine Light)

This light is part of the vehicle

’

s

emission control on-board diagnostic
system. If this light is on while the
engine is running, a malfunction has
been detected and the vehicle may
require service. The light should come
on to show that it is working when
the ignition is in Service Mode. See

Ignition Positions

0

182

.

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

FANATEC Porsche 911 Turbo S Wheel Developer Quick Manual preview
Porsche 911 Turbo S Wheel
Brand: FANATEC Pages: 9
Harbor Freight Tools 92043 Assembly And Operating Instructions preview
92043
Brand: Harbor Freight Tools Pages: 4
Porsche 911 GT3 - Brochure preview
911 GT3 -
Brand: Porsche Pages: 51
Whispbar K710W Fitting Instructions For Basic Carrier preview
K710W
Brand: Whispbar Pages: 14
Subaru 2005 Baja Owner'S Manual preview
2005 Baja
Brand: Subaru Pages: 34
FAAFTECH FT-VF-HND2 Installation Manual preview
FT-VF-HND2
Brand: FAAFTECH Pages: 8
AutoMaxi AXIS XXL Instructions preview
AXIS XXL
Brand: AutoMaxi Pages: 2
PAC GM1A-R Quick Start Manual preview
GM1A-R
Brand: PAC Pages: 4
NavLinkz RL2-SC14 Manual preview
RL2-SC14
Brand: NavLinkz Pages: 21
METRON PC05T User Manual preview
PC05T
Brand: METRON Pages: 4
C-KO RS-4-18-R-I Fitting Instructions preview
RS-4-18-R-I
Brand: C-KO Pages: 4
Mercedes-Benz Sprinter 2003 Manual preview
Sprinter 2003
Brand: Mercedes-Benz Pages: 296
TATA Motors Indigo LE Owner'S Manual & Service Book preview
Indigo LE
Brand: TATA Motors Pages: 151
Thule QUICKDRAW RACHET TIE-DOWNS 855 User Manual preview
QUICKDRAW RACHET TIE-DOWNS 855
Brand: Thule Pages: 3
SAFARI SS18HF Manual preview
SS18HF
Brand: SAFARI Pages: 5
V8 equipment E.BEX Manual preview
E.BEX
Brand: V8 equipment Pages: 34
AllTrade Powerbuilt 648601 Operating Instructions preview
Powerbuilt 648601
Brand: AllTrade Pages: 3
Perrycraft SportQuest Series Installation preview
SportQuest Series
Brand: Perrycraft Pages: 2

Brands by name

Popular brands

Load more brands