manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

DRIVING AND OPERATING

173

If the vehicle slips sideways, it can
hit something that will trip it

—

a

rock, a rut, etc.

—

and roll over.

.

Hidden obstacles can make the
steepness of the incline more
severe. If a rock is driven across
with the uphill wheels, or if the
downhill wheels drop into a rut or
depression, the vehicle can tilt
even more.

.

If an incline must be driven
across, and the vehicle starts to
slide, turn downhill. This should
help straighten out the vehicle and
prevent the side slipping.

{

Warning

Getting out of the vehicle on the
downhill side when stopped across
an incline is dangerous. If the
vehicle rolls over, you could be
crushed or killed. Always get out on
the uphill side of the vehicle and
stay well clear of the rollover path.

Driving in Mud, Sand, Snow,
or Ice

Use a low gear when driving in mud

—

the deeper the mud, the lower the

gear. Keep the vehicle moving to avoid
getting stuck.

Traction changes when driving on
sand. On loose sand, such as on
beaches or sand dunes, the tires tend
to sink into the sand. This affects
steering, accelerating, and braking.
Drive at a reduced speed and avoid
sharp turns or abrupt maneuvers.

Traction is reduced on hard packed
snow and ice and it is easy to lose
control. Reduce vehicle speed when
driving on hard packed snow and ice.

{

Warning

Driving on frozen lakes, ponds,
or rivers can be dangerous. Ice
conditions vary greatly and the
vehicle could fall through the ice;
you and your passengers could
drown. Drive your vehicle on safe
surfaces only.

Driving in Water

{

Warning

Driving through rushing water can
be dangerous. Deep water can
sweep your vehicle downstream and
you and your passengers could
drown. If it is only shallow water, it
can still wash away the ground
from under your tires. Traction
could be lost, and the vehicle could
roll over. Do not drive through
rushing water.

Caution

Do not drive through standing
water if it is deep enough to cover
the wheel hubs, axles, or exhaust
pipe. Deep water can damage the
axle and other vehicle parts.

If the standing water is not too deep,
drive through it slowly. At faster
speeds, water can get into the engine
and cause it to stall. Stalling can

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Toyota 2012 Rav4 Owner'S Manual preview
2012 Rav4
Brand: Toyota Pages: 529
Mazdaspeed QSEA 51 96Z Installation And User Instructions Manual preview
QSEA 51 96Z
Brand: Mazdaspeed Pages: 8
Volkswagen 1973 Convertible Owner'S Manual preview
1973 Convertible
Brand: Volkswagen Pages: 80
walser 30968 User Instructions preview
30968
Brand: walser Pages: 24
Audiovox UniStreamONE Installation Manual preview
UniStreamONE
Brand: Audiovox Pages: 24
Mercedes-Benz GLE Coupe Brief Overview preview
GLE Coupe
Brand: Mercedes-Benz Pages: 2
Westin 25-0560 Instructions preview
25-0560
Brand: Westin Pages: 2
ideus VV950 User Manual preview
VV950
Brand: ideus Pages: 159
Air Lift 88365 Installation Manual preview
88365
Brand: Air Lift Pages: 28
Dolphin DAS400 Owner'S Manual preview
DAS400
Brand: Dolphin Pages: 16
Prorack K947 Fitting Instructions Manual preview
K947
Brand: Prorack Pages: 14
PEUGEOT 5008 2017 Handbook preview
5008 2017
Brand: PEUGEOT Pages: 404
Kargo Master 409CD Installation Manual preview
409CD
Brand: Kargo Master Pages: 7
LetsGoAero V2 Two-Bike Carrier User Manual preview
V2 Two-Bike Carrier
Brand: LetsGoAero Pages: 2
iDataLink ADS-BLADE AL Install Manual preview
ADS-BLADE AL
Brand: iDataLink Pages: 11
Whelen Engineering Company SAK5 Installation Manual preview
SAK5
Brand: Whelen Engineering Company Pages: 2
Directed Install Essentials CAN1 Installation Manual preview
Install Essentials CAN1
Brand: Directed Pages: 23
Toyota 2001 MR2 Spyder Owner'S Manual preview
2001 MR2 Spyder
Brand: Toyota Pages: 234

Brands by name

Popular brands

Load more brands