Cadillac Escalade 2020 Owner'S Manual Download Page 9 | Manualshive

Page: 9 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

KEYS, DOORS, AND WINDOWS

9

Other conditions can affect the
performance of the transmitter. See

Remote Keyless Entry (RKE) System

Q

:

Press to lock all doors and the

fuel door.

If enabled, the turn signal lamps flash
once on the second press to indicate
locking has occurred. If enabled, the
horn chirps when

Q

is pressed again

within three seconds. See

Personalization

If the driver door is open when

Q

is

pressed and Unlocked Door
Anti-Lockout is enabled, all doors will
lock and then the driver door will
immediately unlock. See

Personalization

.

If the passenger door is open when

Q

is pressed, all doors lock.

Pressing

Q

arms the alarm system.

See

Vehicle Alarm System

.

K

:

Press once to unlock the driver

door and the fuel door. If

K

is pressed

again within three seconds, all
remaining doors unlock. The interior
lamps may come on and stay on for
20 seconds or until the ignition is
turned on.

If enabled, the turn signal lamps flash
twice to indicate unlocking has
occurred. If enabled, the exterior
lamps may turn on. See

Personalization

.

Pressing

K

on the RKE transmitter

disarms the alarm system. See

.

Press and hold

K

to remotely open

the windows, if enabled. See

Personalization

.

c

:

Press twice to open the liftglass.

b

:

Press twice to open or close the

liftgate. Press once to stop the liftgate
from moving.

7

:

Press and release to initiate

vehicle locator. The turn signal lamps
flash and the horn sounds three times.

Press and hold

7

for more than

three seconds to activate the panic
alarm. The turn signal lamps flash
and the horn sounds for 30 seconds,

or until

7

is pressed again or the

vehicle is started. The ignition must
be off for the panic alarm to work.

/

:

If equipped, press and release

Q

,

then immediately press and hold

/

until the turn signals flash or for at

«
...
7
8
9
10
11
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: RaceChip Pages: 12

Stratus LHD 1997

Brand: Chrysler Pages: 1534

Brand: Kia Pages: 11

Brand: Saab Pages: 426

Brand: Metra Electronics Pages: 5

Brand: Renkforce Pages: 4

Brand: BMW Pages: 189

2011 A3 Sportback

Brand: Audi Pages: 29

Brand: v.LOGiC Pages: 22

Brand: Softride Pages: 4

Brand: travall Pages: 4

Brand: Westin Pages: 3

Brand: Nav TV Pages: 11

Brand: Metra Electronics Pages: 10

Brand: Audi Pages: 9

Brand: Westin Pages: 2

Brand: Yakima Pages: 10

Brand: Quadratec Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands