Cadillac Escalade 2020 Owner'S Manual Download Page 14 | Manualshive

Page: 14 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

14

KEYS, DOORS, AND WINDOWS

/

:

This button is on the RKE

transmitter for remote start.

The climate control system will use
the previous settings during a remote
start. The rear window defogger may
come on during remote start based on
cold ambient conditions. The rear
window defogger indicator light does
not come on during remote start.

If equipped, the heated steering wheel
may come on during cold weather
when enabled in vehicle
personalization. See

Personalization

If equipped, the heated and ventilated
front seats may also come on when
the vehicle personalization setting is
enabled. See

Heated and Cooled Front

.

Laws in some local communities may
restrict the use of remote starters. For
example, some laws may require a
person using remote start to have the
vehicle in view. Check local
regulations for any requirements.

If your vehicle is low on fuel, do not
use the remote start feature. The
vehicle may run out of fuel.

The RKE transmitter range may be
shorter while the vehicle is running.

Other conditions can affect the
performance of the transmitter. See

Remote Keyless Entry (RKE) System

Starting the Engine Using Remote
Start

1. Press and release

Q

on the RKE

transmitter.

2. Immediately press and hold

/

for at least four seconds or until
the turn signal lamps flash. This
confirms the request to remote
start the vehicle has been
received.

During the remote start, the
doors will be locked and the
parking lamps will remain on as
long as the engine is running.

The engine will shut off after
15 minutes unless a time
extension is done or the vehicle
is started.

3. Press the brake pedal and start

the vehicle to drive.

Extending Engine Run Time

The engine run time can also be
extended by another 15 minutes,
if during the first 15 minutes
Steps 1 and 2 are repeated while the
engine is still running. An extension
can be requested 30 seconds after
starting. This provides a total of
30 minutes.

The remote start can only be
extended once.

When the remote start is extended,
the second 15-minute period is added
on to the first 15 minutes for a total
of 30 minutes.

A maximum of two remote starts, or a
remote start with an extension, are
allowed between ignition cycles.

The vehicle's ignition must be turned
from on to off before the remote start
procedure can be used again.

Canceling a Remote Start

To cancel a remote start, do any of
the following:

.

Press and hold

/

until the

parking lamps turn off.

«
...
12
13
14
15
16
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: A-Tach Mounts Pages: 2

Brand: A-Tach Mounts Pages: 2

Brand: A-Tach Mounts Pages: 2

Brand: Acdeos Pages: 38

Brand: TBC Pages: 12

Brand: Axxess Pages: 8

Brand: SeaSucker Pages: 9

Porsche 911 GT3 R

Brand: iRacing Pages: 25

2010 Civic Sedan

Brand: Honda Pages: 390

Brand: iOttie Pages: 58

Alloy Rugged Ridge X-Clamp

Brand: Omix-Ada Pages: 2

Brand: Dodge Pages: 3

Brand: ULTIMATE SPEED Pages: 40

Brand: S3 Power Sports Pages: 2

2004 Impreza OUTBACK SPORT

Brand: Subaru Pages: 34

Brand: ConWys AG Pages: 16

Brand: Broadfeet Pages: 2

Brand: PEUGEOT Pages: 232

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands