manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

176

DRIVING AND OPERATING

be applied sooner than when on
dry pavement. See

Antilock Brake

System (ABS)

0

198

.

.

Allow greater following distance
and watch for slippery spots. Icy
patches can occur on otherwise
clear roads in shaded areas. The
surface of a curve or an overpass
can remain icy when the
surrounding roads are clear. Avoid
sudden steering maneuvers and
braking while on ice.

.

Turn off cruise control.

Blizzard Conditions

Stop the vehicle in a safe place and
signal for help. Stay with the vehicle
unless there is help nearby. To get
help and keep everyone in the
vehicle safe:

.

Turn on the hazard warning
flashers.

.

Tie a red cloth to an outside
mirror.

{

Warning

Snow can trap engine exhaust
under the vehicle. This may cause
exhaust gases to get inside. Engine
exhaust contains carbon monoxide
(CO), which cannot be seen or
smelled. It can cause
unconsciousness and even death.

If the vehicle is stuck in snow:

.

Clear snow from the base of
the vehicle, especially any
blocking the exhaust pipe.

.

Open a window about 5 cm
(2 in) on the vehicle side that
is away from the wind, to
bring in fresh air.

.

Fully open the air outlets on
or under the instrument
panel.

.

Adjust the climate control
system to circulate the air
inside the vehicle and set the

(Continued)

Warning (Continued)

fan speed to the highest
setting. See

“

Climate Control

Systems.

”

For more information about CO, see

Engine Exhaust

0

188

.

To save fuel, run the engine for short
periods to warm the vehicle and then
shut the engine off and partially close
the window. Moving about to keep
warm also helps.

If it takes time for help to arrive,
when running the engine, push the
accelerator pedal slightly so the
engine runs faster than the idle speed.
This keeps the battery charged to
restart the vehicle and to signal for
help with the headlamps. Do this as
little as possible, to save fuel.

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Allen Sports QR545 Instructions preview
QR545
Brand: Allen Sports Pages: 2
Jeep GLADIATOR 2022 Owner'S Manual preview
GLADIATOR 2022
Brand: Jeep Pages: 380
Voxoa MCU-20A(P40) User Manual preview
MCU-20A(P40)
Brand: Voxoa Pages: 48
MULTILIFT ULTIMA S Installation Instructions Manual preview
ULTIMA S
Brand: MULTILIFT Pages: 62
TomTom LINK 105 Installation Manual preview
LINK 105
Brand: TomTom Pages: 22
Kleinn RS-GM6 Installation Manual preview
RS-GM6
Brand: Kleinn Pages: 8
Whispbar WB201 Manual preview
WB201
Brand: Whispbar Pages: 14
EUFAB 12014 Manual preview
12014
Brand: EUFAB Pages: 20
Toyota 4Runner 1999 Owner'S Manual preview
4Runner 1999
Brand: Toyota Pages: 285
Honda 2010 Accord Coupe Owner'S Manual preview
2010 Accord Coupe
Brand: Honda Pages: 410
TracRac TracVan Double Installation Instructions Manual preview
TracVan Double
Brand: TracRac Pages: 6
Dodge 2005 Sprinter User Manual preview
2005 Sprinter
Brand: Dodge Pages: 60
Quadratec 12033.1001 Assembly & Installation Manual preview
12033.1001
Brand: Quadratec Pages: 4
CAME UNIPARK ARK1 Manual preview
UNIPARK ARK1
Brand: CAME Pages: 14
Hyundai IONIQ HYBRID 2019 Quick Reference Manual preview
IONIQ HYBRID 2019
Brand: Hyundai Pages: 16
Westin 46-24025 Installation Instructions Manual preview
46-24025
Brand: Westin Pages: 9
AdvanceTec Verizon V860 - BARRAGE User Manual preview
Verizon V860 - BARRAGE
Brand: AdvanceTec Pages: 8
Improved Racing EFR-605 Instructions Manual preview
EFR-605
Brand: Improved Racing Pages: 11

Brands by name

Popular brands

Load more brands