Cadillac Escalade 2020 Owner'S Manual Download Page 47 | Manualshive

Page: 47 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

SEATS AND RESTRAINTS

47

5. To activate massage at last

massage type and intensity
settings or to turn massage off,
press the massage On/Off
control (2).

Heated and Cooled Front
Seats

{

Warning

If temperature change or pain to
the skin cannot be felt, the seat
heater may cause burns. To reduce
the risk of burns, use care when
using the seat heater, especially for
long periods of time. Do not place
anything on the seat that insulates
against heat, such as a blanket,
cushion, cover, or similar item. This
may cause the seat heater to
overheat. An overheated seat heater
may cause a burn or may damage
the seat.

To operate, the engine must be
running.

Press

I

or

+

to heat the driver or

passenger seatback only.

Press

J

or

z

to heat the driver or

passenger seat cushion and seatback.

Press

C

or

{

to cool the driver or

passenger seat.

When this feature is off, the heated
and cooled seat symbols on the
buttons are white. When a heated seat
is turned on, the symbol turns red.
When a cooled seat is turned on, the
symbol turns blue.

Press the button once for the highest
setting. With each press of the button,
the seat will change to the next lower
setting, and then to the off setting.
The indicator lights next to the
buttons indicate three for the highest
setting and one for the lowest. If the
heated seats are on high for an
extended time, their level may
automatically be lowered.

The passenger seat may take longer to
heat up.

Remote Start Auto Heated and
Cooled Seats

During a remote start, the heated or
cooled seats will turn on if enabled in
vehicle personalization. When it is
cold outside, the heated seats turn on;
when it is hot outside, the cooled
seats turn on. The seats will continue
to operate depending on the vehicle's
internal temperature. If auto heated or
cooled seats are not equipped or
enabled, seat operation is canceled
when the ignition is turned on. Press
the heated or cooled seat button to
use the heated or cooled seats after

«
...
45
46
47
48
49
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: JAC Pages: 70

Brand: Camoplast Pages: 60

Brand: VanEssa mobilcamping Pages: 8

Brand: Falcon Pages: 8

Prestige APS-45B

Brand: Audiovox Pages: 8

Brand: Volvo Pages: 138

Brand: Cequent Pages: 9

Brand: Yakima Pages: 13

Brand: Menabo Pages: 11

Brand: Boyo Pages: 9

Brand: Volvo Pages: 211

Brand: Rugged Ridge Pages: 3

Brand: AIS Pages: 2

Brand: INDIWORK Pages: 18

Brand: Opel Pages: 103

Brand: Mitsubishi Pages: 362

Brand: Mazda Pages: 1001

Prestige 128-8602

Brand: Audiovox Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands