manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

210

DRIVING AND OPERATING

control is engaged, a green

J

indicator will be lit on the instrument
cluster; the following gap will not
display.

When the vehicle is turned on, the
cruise control mode will be set to the
last mode used before the vehicle was
turned off.

{

Warning

Always check the cruise control
indicator on the instrument cluster
to determine which mode cruise
control is in before using the
feature. If ACC is not active, the
vehicle will not automatically brake
for other vehicles, which could
cause a crash if the brakes are not
applied manually. You and others
could be seriously injured or killed.

Setting Adaptive Cruise Control

If

J

is on when not in use, it could

get pressed and go into ACC when not
desired. Keep

J

off when cruise is

not being used.

Select the set speed desired for ACC.
This is the vehicle speed when no
vehicle is detected in its path.

While the vehicle is moving, ACC will
not set at a speed less than 25 km/h
(15 mph), although it can be resumed
when driving at lower speeds.

To set ACC while moving:

1. Press

J

.

2. Get up to the desired speed.

3. Press and release SET

–

.

4. Remove your foot from the

accelerator.

After ACC is set, it may immediately
apply the brakes if a vehicle ahead is
detected closer than the selected
following gap.

The ACC indicator displays on the
instrument cluster and Head-Up
Display (HUD). When ACC is active,
the indicator will be lit green.

Be mindful of speed limits,
surrounding traffic speeds, and
weather conditions when selecting the
set speed.

Resuming a Set Speed

If ACC is set at a desired speed and
then the brakes are applied, ACC is
disengaged without erasing the set
speed from memory.

To begin using ACC again, press RES+
up briefly.

.

If the vehicle is moving, it returns
to the previous set speed.

.

If the vehicle is stopped with the
brake pedal applied, press RES+
and release the brake pedal. ACC
will hold the vehicle until RES+ or
the accelerator pedal is pressed.

A green ACC indicator and the set
speed display on the instrument
cluster. The vehicle ahead indicator
may be flashing if a vehicle ahead was

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

A-Tach Mounts 50131 Instructions preview
50131
Brand: A-Tach Mounts Pages: 2
EAL Formula 523585 Assembly Instructions preview
Formula 523585
Brand: EAL Pages: 4
Q'STRAINT QLK-150 Installation Instructions Manual preview
QLK-150
Brand: Q'STRAINT Pages: 10
Vauxhall Ampera Owner'S Manual preview
Ampera
Brand: Vauxhall Pages: 199
U & Me Brothers LK-168A Manual preview
LK-168A
Brand: U & Me Brothers Pages: 6
Mini COOPER Owner'S Manual preview
COOPER
Brand: Mini Pages: 20
Right Weigh 221-SK Installation Manual preview
221-SK
Brand: Right Weigh Pages: 16
r.LiNK RL2-MMI3G-GW Manual preview
RL2-MMI3G-GW
Brand: r.LiNK Pages: 21
Carcomm CMPC-22 Fujitsu-Siemens PocketLoox 410 Installation Manual preview
CMPC-22 Fujitsu-Siemens PocketLoox 410
Brand: Carcomm Pages: 2
Curt Manufacturing 58963 Installation Manual preview
58963
Brand: Curt Manufacturing Pages: 4
Whispbar K559W Fitting Instructions Manual preview
K559W
Brand: Whispbar Pages: 112
Mercedes-Benz A 150 Owner'S Manual preview
A 150
Brand: Mercedes-Benz Pages: 305
Volvo S90 TWIN ENGINE Owner'S Manual preview
S90 TWIN ENGINE
Brand: Volvo Pages: 662
CITROEN CX 2000 Repair Manual preview
CX 2000
Brand: CITROEN Pages: 394
KAP HK CARPLAY 10w Instruction Manual preview
HK CARPLAY 10w
Brand: KAP Pages: 22
Honda 2002 Accord Coupe Owner'S Manual preview
2002 Accord Coupe
Brand: Honda Pages: 367
Yakima K1043 Manual preview
K1043
Brand: Yakima Pages: 10
Westin Sportsman 40-0125 Installation Instructions preview
Sportsman 40-0125
Brand: Westin Pages: 2

Brands by name

Popular brands

Load more brands