manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

DRIVING AND OPERATING

191

process, shifting might feel different
as the transmission determines the
best settings.

When temperatures are very cold, the
transmission's gear shifting could be
delayed providing more stable shifts
until the engine warms up. Shifts
could be more noticeable with a cold
transmission. This difference in
shifting is normal.

L :

This position allows selection of a

range of gears appropriate for current
driving conditions. If equipped, see

“

Range Selection Mode

”

under

Manual

Mode

0

191

.

Caution

Spinning the tires or holding the
vehicle in one place on a hill using
only the accelerator pedal may
damage the transmission. The
repair will not be covered by the
vehicle warranty. If the vehicle is
stuck, do not spin the tires. When
stopping on a hill, use the brakes to
hold the vehicle in place.

Normal Mode Grade Braking

This mode is enabled when the
vehicle is started, but is not enabled
in Range Selection Mode. It assists in
maintaining desired vehicle speeds
when driving on downhill grades by
using the engine and transmission to
slow the vehicle. The first time the
system engages for each ignition
cycle, a DIC message will be displayed.

To disable or enable Normal Mode
Grade Braking within the current
ignition cycle, press and hold the
Tow/Haul button for five seconds.
When the button is released, the
requested mode change is made.
A DIC message displays.

For other forms of grade braking, see

Tow/Haul Mode

0

194

and

Cruise Control

0

206

.

Kickdown Mode

The accelerator pedal provides an
additional downshift after pressing
through the kickdown feature.

It requires extra pedal pressure near
the end of its travel to engage.

Manual Mode

Range Selection Mode

If equipped, Range Selection Mode
helps control the vehicle's
transmission and vehicle speed while
driving downhill or towing a trailer by
letting you select a desired range of
gears.

To use this feature:

1. Move the shift lever to

L (Manual Mode).

2. Press the plus/minus buttons on

the shift lever to select the
desired range of gears for current
driving conditions. Or, hold the
plus/minus buttons to select the
highest or lowest range available
for the current vehicle speed.

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Laser 4832 Manual preview
4832
Brand: Laser Pages: 8
Yakima Q46 Installation Instructions preview
Q46
Brand: Yakima Pages: 4
JANE be cool boosty Manual preview
be cool boosty
Brand: JANE Pages: 21
Dakota Digital Retrotech RTX-68D-CHG Quick Start Manual preview
Retrotech RTX-68D-CHG
Brand: Dakota Digital Pages: 4
Romik 2137 2D Installation Instructions Manual preview
2137 2D
Brand: Romik Pages: 6
Waeco MagicComfort MSH200 Installation And Operating Instructions Manual preview
MagicComfort MSH200
Brand: Waeco Pages: 108
Tusk RL-HM018R Installation Instructions And Information Manual preview
RL-HM018R
Brand: Tusk Pages: 2
StowAway 2 025.41 Assembly Instructions preview
025.41
Brand: StowAway 2 Pages: 2
Whelen Engineering Company FastTrax FTF4 Installation Manual preview
FastTrax FTF4
Brand: Whelen Engineering Company Pages: 9
Omix-Ada 11704.05 Owner'S Manual preview
11704.05
Brand: Omix-Ada Pages: 6
RHOX LGT-381L Installation Instructions Manual preview
LGT-381L
Brand: RHOX Pages: 8
Omix-Ada Alloy Rugged Ridge X-Clamp Manual preview
Alloy Rugged Ridge X-Clamp
Brand: Omix-Ada Pages: 2
Dodge 8W-70 Wiring Diagram preview
8W-70
Brand: Dodge Pages: 3
Safe Fleet Prime Design OCM-3032 Quick Start Manual preview
Prime Design OCM-3032
Brand: Safe Fleet Pages: 4
Mitsubishi MOTORS OUTLANDER PHEV 2022 Manual preview
OUTLANDER PHEV 2022
Brand: Mitsubishi MOTORS Pages: 8
iQOS CCU01 Safety Warnings And Instructions preview
CCU01
Brand: iQOS Pages: 4
Bracketron Multi Vehicle Mount MVM-35-05 Installation Manual preview
Multi Vehicle Mount MVM-35-05
Brand: Bracketron Pages: 4
Westin 28-21030 Instructions preview
28-21030
Brand: Westin Pages: 3

Brands by name

Popular brands

Load more brands