manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

DRIVING AND OPERATING

237

If equipped with Lane Change Alert
(LCA), the LCA detection zones that
extend back from the side of the
vehicle do not move further back
when a trailer is towed. Use caution
while changing lanes when towing a
trailer.

If equipped with Rear Cross Traffic
Alert (RCTA), use caution while
backing up when towing a trailer, as
the RCTA detection zones that extend
out from the back of the vehicle do
not move further back when a trailer
is towed.

{

Warning

When towing a trailer, exhaust
gases may collect at the rear of the
vehicle and enter if the liftgate,
trunk/hatch, or rear-most window
is open.

When towing a trailer:

.

Do not drive with the liftgate,
trunk/hatch, or rear-most
window open.

(Continued)

Warning (Continued)

.

Fully open the air outlets on
or under the instrument
panel.

.

Also adjust the climate
control system to a setting
that brings in only outside air.
See

“

Climate Control Systems

”

in the Index.

For more information about carbon
monoxide, see

Engine Exhaust

0

188

.

Towing a trailer requires experience.
The combination of the vehicle and
trailer is longer and not as responsive
as the vehicle itself. Get used to the
handling and braking of the
combination by driving on a level road
surface before driving on public roads.

The trailer structure, the tires, and the
brakes must be all be rated to carry
the intended cargo. Inadequate trailer
equipment can cause the combination
to operate in an unexpected or unsafe
manner. Before driving, inspect all

trailer hitch parts and attachments,
safety chains, electrical connectors,
lamps, tires, and mirrors. See

Towing

Equipment

0

244

. If the trailer has

electric brakes, start the combination
moving and then manually apply the
trailer brake controller to check the
trailer brakes work. During the trip,
occasionally check that the cargo and
trailer are secure and that the lamps
and any trailer brakes are working.

Towing with a Stability Control
System

When towing, the stability control
system might be heard. The system
reacts to vehicle movement caused by
the trailer, which mainly occurs
during cornering. This is normal when
towing heavier trailers.

Following Distance

Stay at least twice as far behind the
vehicle ahead as you would when
driving without a trailer. This can help
to avoid heavy braking and sudden
turns.

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

JETBAG 320 Fitting Instructions Manual preview
320
Brand: JETBAG Pages: 44
RACLET SAFARI Setup And Maintenance Manual preview
SAFARI
Brand: RACLET Pages: 48
RACLET Allegra Manual preview
Allegra
Brand: RACLET Pages: 31
Code 3 WingMan Installation & Operation Manual preview
WingMan
Brand: Code 3 Pages: 8
Safe Fleet PRIME DESIGN VRR-NV200 Manual preview
PRIME DESIGN VRR-NV200
Brand: Safe Fleet Pages: 12
Sears 580.32601 Owner'S Manual preview
580.32601
Brand: Sears Pages: 41
Skoda KAROQ 2017 Owner'S Manual preview
KAROQ 2017
Brand: Skoda Pages: 324
Brink 4698 Fitting Instructions Manual preview
4698
Brand: Brink Pages: 26
Acura RLX 2016 Service Bulletin preview
RLX 2016
Brand: Acura Pages: 7
BMW 325i 1991 Electrical Troubleshooting Manual preview
325i 1991
Brand: BMW Pages: 64
Buick Enclave Owner'S Manual preview
Enclave
Brand: Buick Pages: 394
Yakima FreshSesh PowderHound Manual preview
FreshSesh PowderHound
Brand: Yakima Pages: 18
AutoMaxi SUPRA 44 Montage preview
SUPRA 44
Brand: AutoMaxi Pages: 2
Subaru Forester 2.5X 2003 Technicians Reference Booklet preview
Forester 2.5X 2003
Brand: Subaru Pages: 44
Telwin ST 160 Instruction Manual preview
ST 160
Brand: Telwin Pages: 32
Mitsubishi MIRAGE Service Manual preview
MIRAGE
Brand: Mitsubishi Pages: 300
Mitsubishi 2015 OUTLANDER SPORT/RVR Owner'S Manual preview
2015 OUTLANDER SPORT/RVR
Brand: Mitsubishi Pages: 384
Honda 2013 Civic Coupe Technology Reference Manual preview
2013 Civic Coupe
Brand: Honda Pages: 13

Brands by name

Popular brands

Load more brands