manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

258

VEHICLE CARE

Caution

Failure to use the recommended
engine oil or equivalent can result
in engine damage not covered by
the vehicle warranty.

Viscosity Grade

Use SAE 0W-20 viscosity grade
engine oil.

When selecting an oil of the
appropriate viscosity grade, it is
recommended to select an oil of the
correct specification. See

“

Specification

”

earlier in this section.

Engine Oil Additives/Engine Oil
Flushes

Do not add anything to the oil. The
recommended oils meeting the dexos1
specification are all that is needed for
good performance and engine
protection.

Engine oil system flushes are not
recommended and could cause engine
damage not covered by the vehicle
warranty.

What to Do with Used Oil

Used engine oil contains certain
elements that can be unhealthy for
your skin and could even cause
cancer. Do not let used oil stay on
your skin for very long. Clean your
skin and nails with soap and water,
or a good hand cleaner. Wash or
properly dispose of clothing or rags
containing used engine oil. See the
manufacturer's warnings about the
use and disposal of oil products.

Used oil can be a threat to the
environment. If you change your own
oil, be sure to drain all the oil from
the filter before disposal. Never
dispose of oil by putting it in the trash
or pouring it on the ground, into
sewers, or into streams or bodies of
water. Recycle it by taking it to a place
that collects used oil.

Engine Oil Life System

When to Change Engine Oil

This vehicle has a computer system
that indicates when to change the
engine oil and filter. This is based on a
combination of factors which include

engine revolutions, engine
temperature, and miles driven. Based
on driving conditions, the mileage at
which an oil change is indicated can
vary considerably. For the oil life
system to work properly, the system
must be reset every time the oil is
changed.

When the system has calculated that
oil life has been diminished, it
indicates that an oil change is
necessary. A CHANGE ENGINE OIL
SOON message comes on. Change the
oil as soon as possible within the next
1 000 km (600 mi). It is possible that,
if driving under the best conditions,
the oil life system might indicate that
an oil change is not necessary for up
to a year. The engine oil and filter
must be changed at least once a year
and at this time the system must be
reset. Your dealer has trained service
people who will perform this work and
reset the system. It is also important
to check the oil regularly over the
course of an oil drain interval and
keep it at the proper level.

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Jeep Wrangler 2011 Owner'S Manual preview
Wrangler 2011
Brand: Jeep Pages: 603
Jeep Patriot 2011 User Manual preview
Patriot 2011
Brand: Jeep Pages: 80
TATA Motors Safari Owner'S Manual & Service Book preview
Safari
Brand: TATA Motors Pages: 161
TAUBENREUTHER 16 - 590 Fitting Instructions Manual preview
16 - 590
Brand: TAUBENREUTHER Pages: 11
Yakima SKYBOX Series Manual preview
SKYBOX Series
Brand: Yakima Pages: 15
Zavoli Bora Technical Instructions And Installation Manual preview
Bora
Brand: Zavoli Pages: 26
Ford F-150 2018 Quick Reference Manual preview
F-150 2018
Brand: Ford Pages: 12
EUFAB 12015 Manual preview
12015
Brand: EUFAB Pages: 12
Cadillac 1997 Catera Owner Assistance Information preview
1997 Catera
Brand: Cadillac Pages: 34
Buick Electra 225 1965 Service Manual preview
Electra 225 1965
Brand: Buick Pages: 914
travall TDG-1301 Fitting Instruction preview
TDG-1301
Brand: travall Pages: 2
Gacell 13553 User Manual preview
13553
Brand: Gacell Pages: 12
iArmor EDGE IA-W208 Manual preview
EDGE IA-W208
Brand: iArmor Pages: 6
WATT CARWATT CV12-220C150 User Manual preview
CARWATT CV12-220C150
Brand: WATT Pages: 26
BENDIX A-18 TRAILER ABS Manual preview
A-18 TRAILER ABS
Brand: BENDIX Pages: 40
Toyota RAV4 HV 2016 Quick Reference Manual preview
RAV4 HV 2016
Brand: Toyota Pages: 56
Vauxhall Crossland X 2017 Owner'S Manual preview
Crossland X 2017
Brand: Vauxhall Pages: 245
Acura 08L03-TA1-200A Installation Instructions preview
08L03-TA1-200A
Brand: Acura Pages: 4

Brands by name

Popular brands

Load more brands