manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

VEHICLE CARE

307

5. Remove all of the wheel nuts.

6. Take off the flat tire.

7. Remove any rust or dirt from the

wheel bolts, mounting surfaces,
and spare wheel.

{

Warning

Rust or dirt on a wheel, or on the
parts to which it is fastened, can
make wheel nuts become loose
after time. The wheel could come
off and cause a crash. When
changing a wheel, remove any rust
or dirt from places where the wheel
attaches to the vehicle. In an
emergency, a cloth or a paper towel
can be used; however, use a scraper
or wire brush later to remove all
rust or dirt.

8. Put the wheel nuts back on with

the rounded end of the nuts
toward the wheel after mounting
the spare tire.

{

Warning

Never use oil or grease on bolts or
nuts because the nuts might come
loose. The vehicle's wheel could fall
off, causing a crash.

9. Tighten each wheel nut by hand.

Then use the wheel wrench to
tighten the nuts until the wheel
is held against the hub.

10. Turn the wheel wrench

counterclockwise to lower the
vehicle. Lower the jack
completely.

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Jeep Automobile Service And Warranty Handbook preview
Automobile
Brand: Jeep Pages: 42
Jeep Automobile Warranty Information Booklet preview
Automobile
Brand: Jeep Pages: 44
Cadillac ATS 2015 Convenience/Personalization Manual preview
ATS 2015
Brand: Cadillac Pages: 20
Jeep Automobile Service Contract preview
Automobile
Brand: Jeep Pages: 7
Cadillac 2016 ELR Convenience/Personalization Manual preview
2016 ELR
Brand: Cadillac Pages: 20
Cadillac 2016 CTS Manual preview
2016 CTS
Brand: Cadillac Pages: 354
Cadillac 2005 CTS Personalization Manual preview
2005 CTS
Brand: Cadillac Pages: 20
Cadillac 2014 XTS Convenience/Personalization Manual preview
2014 XTS
Brand: Cadillac Pages: 20
Cadillac ATS 2014 Specifications preview
ATS 2014
Brand: Cadillac Pages: 10
Cadillac 2013 Escalade ESV Owner'S Manual preview
2013 Escalade ESV
Brand: Cadillac Pages: 524
Cadillac 2013 ATS Personalization Manual preview
2013 ATS
Brand: Cadillac Pages: 20
Cadillac ATS 2013 Owenrs Manual preview
ATS 2013
Brand: Cadillac Pages: 438
Cadillac 2013 ATS Owner'S Manual preview
2013 ATS
Brand: Cadillac Pages: 450
Cadillac 2011 Escalade Hybrid Owner'S Manual Addendum preview
2011 Escalade Hybrid
Brand: Cadillac Pages: 94
Cadillac 2011 Escalade Hybrid Owner'S Manual preview
2011 Escalade Hybrid
Brand: Cadillac Pages: 94
Cadillac 2011 CTS COUPE Navigation Manual preview
2011 CTS COUPE
Brand: Cadillac Pages: 78
Cadillac 2011 CTS COUPE Brochure preview
2011 CTS COUPE
Brand: Cadillac Pages: 8
Cadillac 2010 Escalade Manual preview
2010 Escalade
Brand: Cadillac Pages: 113

Brands by name

Popular brands

Load more brands