Cadillac Escalade 2020 Owner'S Manual Download Page 138 | Manualshive

Page: 138 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

138

INSTRUMENTS AND CONTROLS

vehicle's interior temperature. See

“

Auto Heated Seats

”

under in

and Cooled Front Seats

Select Off or On.

Auto Defog

When set to On, the auto defog comes
on when the climate control detects a
humidity risk based on outside temp,
windshield temp, and interior
humidity. Air will be directed on to
the windshield.

Select Off or On.

Auto Rear Defog

If equipped, this feature will
automatically turn on the rear window
defogger when the vehicle is first
started in cold weather and turn off
when the vehicle is warmed.

Select Off or On.

Collision/Detection Systems

Select the Collision/Detection Systems
menu and the following may display:

.

Alert Type

.

Forward Collision System

.

Adaptive Cruise Go Notifier

.

Park Assist

.

Lane Change Alert

.

Rear Cross Traffic Alert

Alert Type

This feature will set crash alerts to
beeps or seat vibrations. This setting
affects all crash alerts including
Forward Collision Alert, Lane
Departure Warning, and Park Assist
alerts. See

Driver Assistance Systems

Select Beeps or Safety Alert Seat.

Forward Collision System

This setting controls the vehicle
response when detecting a vehicle
ahead of you. The Off setting disables
all FCA and AEB functions. With the
Alert and Brake setting, both FCA and
AEB are available. The Alert setting
disables AEB. See

Emergency Braking (AEB)

.

Select Off, Alert and Brake, or Alert.

Adaptive Cruise Go Notifier

This feature will give a reminder that
Adaptive Cruise Control provides
when it has brought the vehicle to a
complete stop behind another
stopping vehicle, and then that vehicle
drives on.

Select Off or On.

Park Assist

If equipped, this allows the feature to
be turned on or off. See

Systems for Parking or Backing

Select Off, On, or On with Towbar
Attached.

Lane Change Alert

This allows the feature to be turned
on or off. See

Lane Change Alert (LCA)

When Lane Change Alert is disabled,
Side Blind Zone Alert is also disabled.

Select Off or On.

Rear Cross Traffic Alert

This allows the feature to be turned
on or off. See

Assistance Systems for

Parking or Backing

«
...
136
137
138
139
140
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: iDataLink Pages: 9

SP200 - QUICKSTART GUIDE 1

Brand: Jabra Pages: 2

BT150 - Headset - Over-the-ear

Brand: Jabra Pages: 2

Brand: Axxess Pages: 8

Brand: SeaSucker Pages: 9

Brand: Maserati Pages: 210

Brand: OnStar Pages: 22

Brand: EZTRUNK Pages: 3

Brand: SAN HIMA Pages: 10

Brand: Scion Pages: 24

Brand: Improved Racing Pages: 17

Brand: Maserati Pages: 302

Brand: Mazda Pages: 3

Brand: Pontiac Pages: 20

Brand: Prime Design Pages: 8

Brand: Scosche Pages: 12

Pro Competition

Brand: G-Tech Pages: 180

KY-700-2018-DRW01

Brand: FALCON RIDGE Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands