Cadillac Escalade 2020 Owner'S Manual Download Page 216 | Manualshive

Page: 216 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

216

DRIVING AND OPERATING

Erasing Speed Memory

The cruise control set speed is erased
from memory if

J

is pressed or if

the ignition is turned off.

Cleaning the Sensing System

The camera sensor on the windshield
ahead of the rearview mirror and the
radar sensors on the front of the
vehicle can become blocked by snow,
ice, dirt, or mud. These areas need to
be cleaned for ACC to operate
properly.

If ACC will not operate, regular Cruise
Control may be available. See

“

Switching Between ACC and Regular

Cruise Control

”

previously in this

section. Always consider driving
conditions before using either cruise
control system.

For cleaning instructions, see

“

Washing the Vehicle

”

under

System operation may also be limited
under snow, heavy rain, or road spray
conditions.

Driver Assistance
Systems

This vehicle may have features that
work together to help avoid crashes or
reduce crash damage while driving,
backing, and parking. Read this entire
section before using these systems.

{

Warning

Do not rely on the Driver
Assistance Systems. These systems
do not replace the need for paying
attention and driving safely. You
may not hear or feel alerts or
warnings provided by these
systems. Failure to use proper care
when driving may result in injury,
death, or vehicle damage. See

Defensive Driving

Under many conditions, these
systems will not:

.

Detect children, pedestrians,
bicyclists, or animals.

(Continued)

Warning (Continued)

.

Detect vehicles or objects
outside the area monitored by
the system.

.

Work at all driving speeds.

.

Warn you or provide you with
enough time to avoid a crash.

.

Work under poor visibility or
bad weather conditions.

.

Work if the detection sensor
is not cleaned or is covered
by ice, snow, mud, or dirt.

.

Work if the detection sensor
is covered up, such as with a
sticker, magnet, or metal
plate.

.

Work if the area surrounding
the detection sensor is
damaged or not properly
repaired.

Complete attention is always
required while driving, and you
should be ready to take action and
apply the brakes and/or steer the
vehicle to avoid crashes.

«
...
214
215
216
217
218
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: N-Com Pages: 28

Brand: AA Products Pages: 8

Brand: Jeda Pages: 8

Brand: Jeep Pages: 496

UNIVERSAL CJ-2A

Brand: Jeep Pages: 27

Brand: Jeep Pages: 228

Brand: Jeep Pages: 108

Brand: Jeep Pages: 525

Brand: Kargo Master Pages: 5

Brand: FormFit Pages: 4

Xplore Pro II SxS

Brand: Marlon Pages: 15

Brand: EUFAB Pages: 12

Brand: NanoCam Plus Pages: 32

Vehicle Asset Communicator

Brand: I.D. Systems Pages: 41

Brand: ACV Pages: 2

Brand: Volvo Pages: 42

TX-STAMP-4-FC04

Brand: Over Armour Offroad Pages: 9

Speed & Route Profiler

Brand: Racelogic Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands