manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

VEHICLE CARE

319

Caution

Do not tow this vehicle with two
wheels on the ground, or vehicle
damage could occur. This damage
would not be covered by the vehicle
warranty.

Dolly towing this vehicle is not
allowed with either the front or the
rear tires on the ground for two-wheel
drive or four-wheel drive, regardless of
transfer case.

Appearance Care

Exterior Care

Locks

Locks are lubricated at the factory.
Use a de-icing agent only when
absolutely necessary, and have the
locks greased after using. See

Recommended Fluids and Lubricants

0

336

.

Washing the Vehicle

To preserve the vehicle's finish, wash
it often and out of direct sunlight.

Caution

Do not use petroleum-based, acidic,
or abrasive cleaning agents as they
can damage the vehicle's paint,
metal, or plastic parts. If damage
occurs, it would not be covered by
the vehicle warranty. Approved
cleaning products can be obtained
from your dealer. Follow all
manufacturer directions regarding

(Continued)

Caution (Continued)

correct product usage, necessary
safety precautions, and appropriate
disposal of any vehicle care
product.

Caution

Avoid using high-pressure washes
closer than 30 cm (12 in) to the
surface of the vehicle. Use of power
washers exceeding 8 274 kPa
(1,200 psi) can result in damage or
removal of paint and decals.

Caution

Do not power wash any component
under the hood that has this

e

symbol.

This could cause damage that
would not be covered by the vehicle
warranty.

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Kargo Master 40640 Assembly Manual preview
40640
Brand: Kargo Master Pages: 5
Toyota 2012 Rav4 Owner'S Manual preview
2012 Rav4
Brand: Toyota Pages: 529
Harken Hoister SUP Manual preview
SUP
Brand: Harken Hoister Pages: 12
Yamaha Raptor Instruction Supplement preview
Raptor
Brand: Yamaha Pages: 2
kaarta STENCIL PRO Assembly & Use preview
STENCIL PRO
Brand: kaarta Pages: 29
Fab Fours BLACK STEEL S2560 Installation Instructions Manual preview
BLACK STEEL S2560
Brand: Fab Fours Pages: 9
iArmor IA-N179 Manual preview
IA-N179
Brand: iArmor Pages: 6
CARRYBOY CB-796IG2-CIGD-R Installation Manual preview
CB-796IG2-CIGD-R
Brand: CARRYBOY Pages: 4
GMC 2012 Terrain Owner'S Manual preview
2012 Terrain
Brand: GMC Pages: 428
Menabo JUZA Fitting Instructions Manual preview
JUZA
Brand: Menabo Pages: 12
Volvo 1996 960 Quick Tips preview
1996 960
Brand: Volvo Pages: 10
Hyundai Santa Fe 2019 Getting Started Manual preview
Santa Fe 2019
Brand: Hyundai Pages: 18
T-Mobile SyncUP DRIVE Start Manual preview
SyncUP DRIVE
Brand: T-Mobile Pages: 2
ULTIMATE SPEED UAWSO 2 B1 Operation And Safety Notes preview
UAWSO 2 B1
Brand: ULTIMATE SPEED Pages: 32
Chevrolet 1998 Tahoe Manual preview
1998 Tahoe
Brand: Chevrolet Pages: 441
Air Lift 88365 Installation Manual preview
88365
Brand: Air Lift Pages: 28
Dolphin DAS400 Owner'S Manual preview
DAS400
Brand: Dolphin Pages: 16
Discount Car Stereo A2DIY-MBR Quick Start Bluetooth Installation Manual preview
A2DIY-MBR
Brand: Discount Car Stereo Pages: 8

Brands by name

Popular brands

Load more brands