background image

Jeep JT 3.5” Spring Lift

www.TERAFLEX.com

1

Revision B

999376

Tools Needed:

- Metric Sockets and Open End Wrenches              - Factory Service Manual

- Torque Wrench                                                         - General Mechanics Tools

Maintenance Note:

After the first 300 miles and every 3,000 miles after that, re-torque all the suspension                 

components and bolts.

Important Notes:

Prior to beginning this install, or any installation, read the instructions thoroughly to familiarize yourself with 

the required steps. Evaluate if you are experienced and capable to personally perform these modifications.              

A factory service manual should be used in conjunction with these installation instructions.

This  product  will  change  the  highway  handling  characteristics  of  your  vehicle,  exercise  caution. After 

altering the suspension it is always advisable to have an alignment done by a competent 4 wheel drive 

shop or by an alignment shop that is experienced with lifted 4 wheel drive vehicles.

Refer to the parts list to ensure that all necessary components and hardware has been included. If any 

parts are missing please contact your local TeraFlex dealer for assistance.

# 1365000

# 2013000

# 2023000

# 2033000

Summary of Contents for 1365000



















Reviews: