manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

KEYS, DOORS, AND WINDOWS

27

Fast Flash :

Vehicle is unsecured.

A door, the liftgate, or the hood
is open.

Slow Flash :

Alarm system is armed.

Arming the Alarm System

1. Turn off the vehicle.

2. Lock the vehicle in one of

three ways:

.

Use the RKE transmitter.

.

Use the Keyless Access
system.

.

With a door open, press

Q

on the interior of the door.

3. After 30 seconds, the alarm

system will arm and the
indicator light will begin to
slowly flash. Pressing

Q

on the

RKE transmitter a second time
will bypass the 30-second delay
and immediately arm the alarm
system.

The vehicle alarm system will not arm
if the doors are locked with the key.

If the driver door is opened without
first unlocking with the RKE
transmitter, the horn will chirp and
the lights will flash to indicate
pre-alarm. If the vehicle is not started,
or the door is not unlocked by
pressing

K

on the RKE transmitter

during the 10-second pre-alarm, the
alarm will be activated.

The alarm will also be activated if a
passenger door, the liftgate, or the
hood is opened without first
disarming the system. When the
alarm is activated, the turn signals
flash and the horn sounds for about
30 seconds. The alarm system will
then re-arm to monitor for the next
unauthorized event.

Disarming the Alarm System

To disarm the alarm system or turn
off the alarm if it has been activated:

.

Press

K

on the RKE transmitter.

.

Unlock the vehicle using the
Keyless Access system.

.

Start the vehicle.

To avoid setting off the alarm by
accident:

.

Lock the vehicle after all
occupants have exited.

.

Always unlock a door with the
RKE transmitter, or use the
Keyless Access system.

Unlocking the driver door with the
key will not disarm the system or
turn off the alarm.

How to Detect a Tamper
Condition

If

K

is pressed on the RKE

transmitter and the horn chirps and
the lights flash three times, an alarm
occurred previously while the alarm
system was armed.

If the alarm has been activated, a
message will appear on the DIC.

Steering Column Lock

If equipped, the steering column lock
is a theft-deterrent device. This
feature locks the steering column
when the vehicle is turned off and the
driver door is opened, or when the

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Saleen 10-8002-C11998B Installation Manual preview
10-8002-C11998B
Brand: Saleen Pages: 12
Buick 2013 Buick Verano Manual preview
2013 Buick Verano
Brand: Buick Pages: 5
Chariot Carriers 51100913 Instruction Manual preview
51100913
Brand: Chariot Carriers Pages: 3
Harbor Freight Tools 66242 User Manual preview
66242
Brand: Harbor Freight Tools Pages: 12
Honda 0SR95-HL4-211A Installation Instructions preview
0SR95-HL4-211A
Brand: Honda Pages: 3
Skoda OCTAVIA - TECHNICAL CHANGES 11-2009 Owner'S Manual Supplement preview
OCTAVIA - TECHNICAL CHANGES 11-2009
Brand: Skoda Pages: 16
EUFAB 16458 Operating Instructions Manual preview
16458
Brand: EUFAB Pages: 16
Bestop Bikini Installation Instructions preview
Bikini
Brand: Bestop Pages: 5
PowerMadd Tri-mount Installation Instructions preview
Tri-mount
Brand: PowerMadd Pages: 3
Safe Fleet PRIME DESIGN VCR-TC11B Assembly Instructions Manual preview
PRIME DESIGN VCR-TC11B
Brand: Safe Fleet Pages: 12
Prorack K577W Fitting Instructions Manual preview
K577W
Brand: Prorack Pages: 15
Volvo 30795637 User Manual preview
30795637
Brand: Volvo Pages: 92
Arrista SG8-19 Installation Manual preview
SG8-19
Brand: Arrista Pages: 2
CITROEN 1953 Traction Avant User Manual preview
1953 Traction Avant
Brand: CITROEN Pages: 26
Speedtech 64-67 Instructional Manual preview
64-67
Brand: Speedtech Pages: 12
Jeep WG Grand Cherokee 2002 Service Manual preview
WG Grand Cherokee 2002
Brand: Jeep Pages: 74
Ace K9 HA-2520 Installation Manual preview
HA-2520
Brand: Ace K9 Pages: 14
Buick 2010 Lucerne Owner'S Manual preview
2010 Lucerne
Brand: Buick Pages: 475

Brands by name

Popular brands

Load more brands