Cadillac Escalade 2020 Owner'S Manual Download Page 125 | Manualshive

Page: 125 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

INSTRUMENTS AND CONTROLS

125

LKA will not assist or alert if the turn
signal is active in the direction of the
lane departure, or if LKA detects that
you are accelerating, braking,
or actively steering.

See

Lane Keep Assist (LKA)

Vehicle Ahead Indicator

If equipped, this indicator will display
green when a vehicle is detected
ahead and amber when you are
following a vehicle ahead much too
closely.

See

Forward Collision Alert (FCA)

.

Traction Off Light

This light comes on briefly while
starting the engine. If it does not,
have the vehicle serviced by your
dealer. If the system is working
normally, the indicator light then
turns off.

The traction off light comes on when
the Traction Control System (TCS) has
been turned off by pressing and
releasing the TCS/StabiliTrak/ESC
button.

This light and the StabiliTrak/ESC OFF
light come on when StabiliTrak/
Electronic Stability Control (ESC) is
turned off.

If the TCS is off, wheel spin is not
limited. Adjust driving accordingly.

See

Traction Control/Electronic Stability

StabiliTrak OFF Light

This light comes on briefly while
starting the engine. If it does not,
have the vehicle serviced by your
dealer.

This light comes on when the
StabiliTrak/Electronic Stability Control
(ESC) system is turned off.
If StabiliTrak/ESC is off, the Traction
Control System (TCS) is also off.

If StabiliTrak/ESC and TCS are off, the
system does not assist in controlling
the vehicle. Turn on the TCS and the
StabiliTrak/ESC systems, and the
warning light turns off.

See

Traction Control/Electronic Stability

«
...
123
124
125
126
127
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: J-Top Pages: 2

Brand: Jeep Pages: 25

Brand: Jeep Pages: 51

Brand: Farenheit Pages: 8

PACCAR PACMOBILE 20

Brand: DAF Pages: 18

Brand: FALCON RIDGE Pages: 4

Brand: A-Tach Mounts Pages: 2

Brand: Metra Electronics Pages: 20

3 Facelift 2006

Brand: Mazda Pages: 94

Brand: AutoLoc Pages: 6

Prime Design VBI-FT31B

Brand: Safe Fleet Pages: 12

Brand: Classic AutoAir Pages: 44

Brand: ECS Electronics Pages: 42

PRIME DESIGN UXV 211

Brand: Safe Fleet Pages: 8

Brand: 3SIXT Pages: 4

Brand: PEUGEOT Pages: 67

Brand: Prorack Pages: 15

Brand: N2MB Racing Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands