Cadillac Escalade 2020 Owner'S Manual Download Page 106 | Manualshive

Page: 106 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

106

INSTRUMENTS AND CONTROLS

z

AUTO :

Press to turn Rainsense

on or off. When turned on and

z

FRONT is in one of the Rainsense
wipe sensitivity positions the wipers
can be adjusted for more or less
sensitivity to moisture. When turned
off, the wipers operate as timed
intermittent wipers and can be
adjusted for more or less frequent
wipes.

If

z

AUTO is turned on when the

ignition is turned on, or if the ignition

is on and the

z

FRONT band is in

one of the sensitivity settings when

z

AUTO is turned on or off, a

message may display indicating if
Rainsense was turned on or off.

If the ignition is on and

z

FRONT

is not in one of the sensitivity settings

when

z

AUTO is turned on, a

message may display indicating that
the wiper band must be in one of the
sensitivity settings for Rainsense to
operate.

Wiper Arm Assembly Protection

When using an automatic car wash,
move the windshield wiper lever to
OFF. This disables the automatic
Rainsense windshield wipers.

With Rainsense, if the transmission is
in N (Neutral) and the vehicle speed is
very slow, the wipers will
automatically stop at the base of the
windshield.

The wiper operations return to normal
when the transmission is no longer in
N (Neutral) or the vehicle speed has
increased.

Windshield Washer

L

m

:

Push the paddle marked with

the windshield washer symbol at the
top of the turn signal lever to spray

washer fluid and activate the wipers.
The wipers will continue until the
paddle is released or the maximum
wash time is reached. When the
paddle is released, additional wipes
may occur depending on how long the
windshield washer had been activated.
See

for

information on filling the windshield
washer fluid reservoir.

Rear Window Wiper/
Washer

The rear wiper control is on the turn
signal lever.

To turn the rear wiper on, slide the
lever to a wiper position.

OFF :

Turns the wiper off.

INT :

Turns on the rear wiper with a

delay between wipes.

«
...
104
105
106
107
108
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: Saab Pages: 75

Cherokee 16 1982

Brand: Jeep Pages: 1311

10-8002-C11670C

Brand: Saleen Pages: 17

Brand: minnid Pages: 44

DLD Wide Range II

Brand: VDO Pages: 84

TravelCharge Companion GO-Plus

Brand: Wagan Pages: 3

Brand: Jeep Pages: 380

Brand: Cadillac Pages: 522

Brand: mtf TRANSPORT SYSTEM Pages: 9

Electra 225 1965

Brand: Buick Pages: 914

XEBRA ZAPCAR Series

Brand: Zap Pages: 16

Brand: Gator Pages: 8

Brand: benbat Pages: 14

Brand: SPL Pages: 5

2005 JR41 Stratus

Brand: Dodge Pages: 293

Brand: Oldsmobile Pages: 380

Brand: Axxess Pages: 4

ChargePoint CT500-DSTAND

Brand: Coulomb Technologies Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands