manualshive.com logo in svg

Cadillac Escalade 2020, Owner'S Manual

The Cadillac Escalade 2020 Owner's Manual is now available for download, absolutely free! This comprehensive manual is a must-have for every Escalade owner, providing essential information and guidance. Visit manualshive.com now to access and download your manual instantly, ensuring a seamless ownership experience.

Share
Download
background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

28

KEYS, DOORS, AND WINDOWS

driver door is opened and then the
vehicle is turned off. The steering
column unlocks when the vehicle is
turned on.

The Driver Information Center (DIC)
may display one of these messages:

.

A message to service the steering
column lock indicates that an
issue has been detected with the
column lock feature and the
vehicle should be serviced.

.

A message that the steering
column is locked indicates that
the engine is running, but the
steering column is still locked. It is
normal for the column to be
locked during a remote start, but
the column should unlock after
the brake pedal is pressed and the
vehicle is started. No message will
display during a remote start.

.

A message that the steering wheel
must be turned and the vehicle
must be started again indicates
that the column lock mechanism
is bound, the column locking
device was unable to unlock the
steering column, and the vehicle

did not start. If this happens,
immediately turn the steering
wheel from side to side to unbind
the column lock. If this does not
unlock the steering column, turn
the vehicle off and open the driver
door to reset the system. Then
turn the vehicle on and
immediately turn the steering
wheel side to side for about
15 seconds. In some cases, it may
take significant force to unbind
the column.

To keep the steering column from
binding, straighten the front wheels
before turning off the vehicle.

Immobilizer Operation

This vehicle has a passive
theft-deterrent system.

The system does not have to be
manually armed or disarmed.

The vehicle is automatically
immobilized when the vehicle is
turned off.

The immobilization system is
disarmed when the ignition is on and
a valid transmitter is found in the
vehicle.

The security light in the instrument
cluster comes on if there is a problem
with arming or disarming the
theft-deterrent system.

The system has one or more
transmitters matched to an
immobilizer control unit in the
vehicle. Only a correctly matched
transmitter will start the vehicle.
If the transmitter is ever damaged,
you may not be able to start the
vehicle.

If the engine does not start and the
security light stays on, there is a
problem with the system. Turn the
vehicle off and try again.

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

CAMPARK R10 Manual preview
R10
Brand: CAMPARK Pages: 20
Jacob Jensen Electronic Parking Disc 3 Quick Manual preview
Electronic Parking Disc 3
Brand: Jacob Jensen Pages: 2
Yakima K1005 Instructions Manual preview
K1005
Brand: Yakima Pages: 12
Blue Giant STRONGARM RVR303 Installation & Technical Manual preview
STRONGARM RVR303
Brand: Blue Giant Pages: 48
StowAway 2 025.41 Assembly Instructions preview
025.41
Brand: StowAway 2 Pages: 2
Pyle PLDCP3 User Manual preview
PLDCP3
Brand: Pyle Pages: 2
Hudson 1933 Eight Owner'S Manual preview
1933 Eight
Brand: Hudson Pages: 34
Guidosimplex 907P User Manual preview
907P
Brand: Guidosimplex Pages: 8
INDIWORK A-LINK2-NTG5 Instruction Manual preview
A-LINK2-NTG5
Brand: INDIWORK Pages: 18
Opel CORSA 2020 Infotainment Manual preview
CORSA 2020
Brand: Opel Pages: 103
Acura RLX 2016 Service Bulletin preview
RLX 2016
Brand: Acura Pages: 7
WABCO TEBS E Manual preview
TEBS E
Brand: WABCO Pages: 224
Subaru 2015 Forester Quick Reference Manual preview
2015 Forester
Brand: Subaru Pages: 16
Vauxhall 2013 Zafira Tourer Owner'S Manual preview
2013 Zafira Tourer
Brand: Vauxhall Pages: 289
Audiovox Electronics HR7012M Installation Manual preview
HR7012M
Brand: Audiovox Electronics Pages: 12
Valueline SVL-CARCAM11 User Manual preview
SVL-CARCAM11
Brand: Valueline Pages: 40
Octocam ECO VEDR Technical Manual preview
ECO VEDR
Brand: Octocam Pages: 35
Active Controls ActiveStart ACS30P Installation, Operation & Application Manual preview
ActiveStart ACS30P
Brand: Active Controls Pages: 2

Brands by name

Popular brands

Load more brands