Cadillac Escalade 2020 Owner'S Manual Download Page 18 | Manualshive

Page: 18 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

18

KEYS, DOORS, AND WINDOWS

Automatic Door Locks

The doors will lock automatically
when all doors are closed, the ignition
is on, and the vehicle is shifted out of
P (Park).

If a vehicle door is unlocked and then
opened and closed, the doors will lock
either when your foot is removed from
the brake or the vehicle speed
becomes faster than 13 km/h (8 mph).

To unlock the doors:

.

Press

K

on the power door lock

switch.

.

Shift the transmission into
P (Park).

Automatic door locking and unlocking
cannot be programmed.

Lockout Protection

If the ignition is on or in ACC/
ACCESSORY and the power door lock
switch is pressed with the driver door
open, all the doors will lock and only
the driver door will unlock.

If the vehicle is off and locking is
requested while a door is open, when
all doors are closed the vehicle will
check for RKE transmitters inside.
If an RKE transmitter is detected and
the number of RKE transmitters inside
has not reduced, the driver door will
unlock and the horn will chirp three
times.

Lockout Protection can be manually
overridden with the driver door open
by pressing and holding

Q

on the

power door lock switch.

Unlocked Door Anti-Lockout

If Unlocked Door Anti-Lockout is
turned on and the vehicle is off, the
driver door is open, and locking is
requested, all the doors will lock and
the driver door will remain open. The
Unlocked Door Anti-Lockout feature
can be turned on or off. See

Personalization

.

Safety Locks

The rear door safety locks prevent
passengers from opening the rear
doors from inside the vehicle.

Press

{

to activate the safety locks on

the rear doors. The indicator light
comes on when activated.

Press

{

again to deactivate the safety

locks.

«
...
16
17
18
19
20
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: TBC Pages: 12

2004 Vibe Navigation System

Brand: Pontiac Pages: 44

Brand: Icom Pages: 20

Brand: Volvo Pages: 24

Brand: Thule Pages: 8

Brand: Whispbar Pages: 15

RUDDER ANGLE INDICATOR

Brand: VDO Pages: 8

Brand: Chevrolet Pages: 372

Brand: AEM Pages: 27

Park Vision VAL632210

Brand: Valeo Pages: 25

Brand: ECS Pages: 4

Brand: Whispbar Pages: 15

Brand: v.link Pages: 19

Brand: Mazda Pages: 3

Brand: Thule Pages: 8

FlashLogic FLC-FORS-FO1B-FLRSFO1-EN

Brand: ADS Pages: 25

Brand: Westfalia Pages: 10

Brand: Mitsubishi Pages: 367

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands