Cadillac Escalade 2020 Owner'S Manual Download Page 88 | Manualshive

Page: 88 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

88

SEATS AND RESTRAINTS

row. Be sure to use an anchor located
directly behind the seating position
where the child restraint will be
placed.

Second Row Seat

—

60/40

For models with 60/40 second row
seating, the top tether anchors are at
the bottom rear of the seat cushion
for each seating position in the second
row. Be sure to use an anchor located
directly behind the seating position
where the child restraint will be
placed.

Third Row Seat

For the third row seat, the top tether
anchors are on the back of the
seatback. Move the flipper panel
rearward to access the anchors. Be
sure to use an anchor located directly
behind the seating position where the
child restraint will be placed.

Do not secure a child restraint in a
position without a top tether anchor if
a national or local law requires that
the top tether be attached, or if the
instructions that come with the child
restraint say that the top tether must
be attached.

According to accident statistics,
children and infants are safer when
properly restrained in a child restraint
system or infant restraint system
secured in a rear seating position. See

Where to Put the Restraint

for

additional information.

Securing a Child Restraint
Designed for the LATCH System

{

Warning

A child could be seriously injured or
killed in a crash if the child
restraint is not properly attached to
the vehicle using either the LATCH
anchors or the vehicle seat belt.
Follow the instructions that came
with the child restraint and the
instructions in this manual.

«
...
86
87
88
89
90
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: IAME Pages: 17

Brand: Whispbar Pages: 16

Brand: CITROËN Pages: 301

Brand: Whispbar Pages: 15

Brand: Toyota Pages: 52

Brand: Kuda Pages: 3

Brand: TAUBENREUTHER Pages: 8

Brand: SAN HIMA Pages: 7

Peterbilt SmartAir

Brand: Paccar Pages: 58

Brand: Mercedes-Benz Pages: 153

Brand: Thule Pages: 8

Brand: Pontiac Pages: 486

Brand: Skoda Pages: 2

Brand: Thule Pages: 8

Brand: Acura Pages: 7

Brand: Thule Pages: 4

Brand: Volvo Pages: 10

Brand: Roadmaster Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands