Cadillac Escalade 2020 Owner'S Manual Download Page 271 | Manualshive

Page: 271 / 355

background image

Cadillac Escalade Owner Manual (GMNA-Localizing-MidEast-13566599) -

2020 - CRC - 5/29/19

VEHICLE CARE

271

3. Try to start the engine in each

gear. The vehicle should start
only in P (Park) or N (Neutral).
If the vehicle starts in any other
position, contact your dealer for
service.

Automatic Transmission
Shift Lock Control Function
Check

{

Warning

When you are doing this inspection,
the vehicle could move suddenly.
If the vehicle moves, you or others
could be injured.

1. Before starting this check, be

sure there is enough room
around the vehicle. It should be
parked on a level surface.

2. Apply the parking brake. Be

ready to apply the regular brake
immediately if the vehicle begins
to move.

3. With the engine off, turn the

ignition on, but do not start the
engine. Without applying the
regular brake, try to move the
shift lever out of P (Park) with
normal effort. If the shift lever
moves out of P (Park), contact
your dealer for service.

Park Brake and P (Park)
Mechanism Check

{

Warning

When you are doing this check, the
vehicle could begin to move. You or
others could be injured and
property could be damaged. Make
sure there is room in front of the
vehicle in case it begins to roll. Be
ready to apply the regular brake at
once should the vehicle begin
to move.

Park on a fairly steep hill, with the
vehicle facing downhill. Keeping your
foot on the regular brake, set the
parking brake.

.

To check the parking brake's
holding ability: With the engine
running and the transmission in
N (Neutral), slowly remove foot
pressure from the regular brake
pedal. Do this until the vehicle is
held by the parking brake only.

.

To check the P (Park) mechanism's
holding ability: With the engine
running, shift to P (Park). Then
release the parking brake followed
by the regular brake.

Contact your dealer if service is
required.

Wiper Blade Replacement

Windshield wiper blades should be
inspected for wear or cracking.

For the proper type and size, see

Maintenance Replacement Parts

.

Caution

Allowing the wiper arm to touch
the windshield when no wiper blade
is installed could damage the

(Continued)

«
...
269
270
271
272
273
...
»

Summary of Contents for Escalade 2020




































































































































































































































































































































































Reviews:

No comments

Related manuals for Escalade 2020

Brand: Federal Signal Corporation Pages: 13

Brand: AC Schnitzer Pages: 16

Brand: Porsche Pages: 195

Brand: WABCO Pages: 32

Brand: iArmor Pages: 4

Brand: Flash Cover Pages: 2

Brand: CTEK Pages: 84

Brand: RHOX Pages: 8

Brand: TOPPOINT Pages: 2

Stargazer Spirit XTR Skylight

Brand: Lippert Pages: 8

Brand: Prorack Pages: 13

Brand: Volvo Pages: 62

Brand: Ranger design Pages: 22

Brand: Magneti Marelli Pages: 3

Brand: Ranger design Pages: 6

Brand: American muscle Pages: 3

Brand: SoundMax Pages: 20

Brand: Honda Pages: 435

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands